Non-volatile memory
Computer memory types |
---|
Volatile |
RAM |
|
Historical |
|
Non-volatile |
ROM |
|
NVRAM |
|
Early stage NVRAM |
|
Magnetic |
|
Optical |
|
In development |
|
Historical |
|
Non-volatile memory (NVM) or non-volatile storage is a type of computer memory that can retrieve stored information even after having been power cycled. In contrast, volatile memory needs constant power in order to retain data. Examples of non-volatile memory include read-only memory, flash memory, ferroelectric RAM, most types of magnetic computer storage devices (e.g. hard disk drives, solid state drives, floppy disks, and magnetic tape), optical discs, and early computer storage methods such as paper tape and punched cards.[1]
Non-volatile memory can be classified as traditional non-volatile disk storage, or storage in non-volatile memory chips (Flash memory Storage) – EEPROM, SSD, NAND, etc.
Contents
1 Overview
2 Electrically addressed
2.1 Read-mostly devices
2.2 Flash memory
2.3 Ferroelectric RAM (F-RAM)
2.4 Magnetoresistive RAM (MRAM)
3 Mechanically addressed systems
4 Organic
5 Non-volatile main memory
6 Specifications
7 References
8 External links
Overview
Non-volatile memory is typically used for the task of secondary storage, or long-term persistent storage.[2] The most widely used form of primary storage today is a volatile form of random access memory (RAM), meaning that when the computer is shut down, anything contained in RAM is lost. However, most forms of non-volatile memory have limitations that make them unsuitable for use as primary storage. Typically, non-volatile memory costs more, provides lower performance, or have limited lifetime compared to volatile random access memory.
Non-volatile data storage can be categorized into electrically addressed systems (read-only memory) and mechanically addressed systems (hard disks, optical disc, magnetic tape, holographic memory, and such).[3][4] Generally speaking, electrically addressed systems are expensive, have limited capacity, but are fast, whereas mechanically addressed systems are more cost effective per bit, but are slower.
Electrically addressed
Electrically addressed semiconductor non-volatile memories can be categorized according to their write mechanism. [Mask ROM]s are factory programmable only, and typically used for large-volume products not required to be updated after manufacture. Programmable read-only memory can be altered after manufacture, but require a special programmer and usually cannot be programmed while in the target system. The programming is permanent and further changes require replacement of the device. Data is stored by physically altering (burning) storage sites in the device.
Read-mostly devices
An EPROM is an erasable ROM that can be changed more than once. However, writing new data to an EPROM requires a special programmer circuit. EPROMs have a quartz window that allows them to be erased with ultraviolet light, but the whole device is cleared at one time. A one-time programmable (OTP) device uses an EPROM chip but omits the quartz window in the package; this is less costly to manufacture. An electrically erasable programmable read-only memory EEPROM uses electrical signals to erase memory. These erasable memory devices require a significant amount of time to erase data and to write new data; they are not usually configured to be programmed by the processor of the target system. Data is stored by use of floating-gate transistors which require special operating voltages to be applied to trap or release electric charge on an insulated control gate for storage sites.
Flash memory
The flash memory chip is a close relative to the EEPROM; it differs in that it can only erase one block or "page" at a time. It is a solid-state chip that maintains stored data without any external power source.[5] Capacity is substantially larger than that of an EEPROM, making these chips a popular choice for digital cameras and desktop PC BIOS chips.
Flash memory devices use two different logical technologies—NOR and NAND—to map data. NOR flash provides high-speed random access, reading and writing data in specific memory locations; it can retrieve as little as a single byte. NAND flash reads and writes sequentially at high speed, handling data in small blocks called pages, however it is slower on read when compared to NOR. NAND flash reads faster than it writes, quickly transferring whole pages of data. Less expensive than NOR flash at high densities, NAND technology offers higher capacity for the same-size silicon.[5]
Ferroelectric RAM (F-RAM)
Ferroelectric RAM (FeRAM, F-RAM or FRAM) is a random-access memory similar in construction to DRAM but (instead of a dielectric layer like in DRAM) contains a thin ferroelectric film of lead zirconate titanate [Pb(Zr,Ti)O3], commonly referred to as PZT. The Zr/Ti atoms in the PZT change polarity in an electric field, thereby producing a binary switch. Unlike RAM devices, F-RAM retains its data memory when power is shut off or interrupted, due to the PZT crystal maintaining polarity. Due to this crystal structure and how it is influenced, F-RAM offers distinct properties from other nonvolatile memory options, including extremely high, although not infinite, endurance (exceeding 1016 read/write cycles for 3.3 V devices), ultra low power consumption (since F-RAM does not require a charge pump like other non-volatile memories), single-cycle write speeds, and gamma radiation tolerance.[6]
Magnetoresistive RAM (MRAM)
Magnetoresistive RAM is one of the newest approaches to non-volatile memory and stores data in magnetic storage elements called magnetic tunnel junctions (MTJs). MRAM has an especially promising future as it seeks to encompass all the desirable features of the other popular types of memory (non-volatility, infinite endurance, high-speed reading/writing, low cost).[7]
The first generation of MRAM, such as Everspin Technologies' 4 Mbit, utilized field-induced writing. The second generation is developed mainly through two approaches: Thermal-assisted switching (TAS)[7] which is being developed by Crocus Technology, and Spin-transfer torque (STT) which Crocus, Hynix, IBM, and several other companies are developing.[when?][8]
Mechanically addressed systems
Mechanically addressed systems utilize a contact structure ("head") to read and write on a designated storage medium. Since circuitry layout is not a key factor for data density, the amount of storage is typically much larger than for electrically addressed systems.[citation needed]
Since the access time depends on the physical location of the data on the device, mechanically addressed systems may not be "random access" as are electrically addressed semiconductor NVRAM. For example, magnetic tape stores data as a sequence of bits on a long tape; transporting the tape past the read/write head is required to access any part of the storage. Tape media can be removed from the drive and stored, giving indefinite capacity at the cost of the time required to retrieve a dismounted tape.[9][10]
Hard disk drives use a rotating magnetic disk to store data; access time is longer than for semiconductor memory, but cost per stored data bit is very low, and they provide random access to any location on the disk. Formerly, removable disk packs were common, allowing storage capacity to be expanded. Optical discs store data by altering a pigment layer on a plastic disk, and are similarly random access. Read-only and read-write versions are available; removable media again allows indefinite expansion, and some automated systems were used to retrieve and mount disks under direct program control.[11][12][13]
Organic
There are polymer printed ferroelectric memory.
Thin Film Electronics ("Thinfilm") produces rewriteable non-volatile organic memory based on ferroelectric polymers. Thinfilm successfully demonstrated roll-to-roll printed memories in 2009.[14][15][16]
In Thinfilm's organic memory the ferroelectric polymer is sandwiched between two sets of electrodes in a passive matrix. Each crossing of metal lines is a ferroelectric capacitor and defines a memory cell. This gives a non-volatile memory comparable to ferroelectric RAM technologies and offer the same functionality as flash memory.
Non-volatile main memory
Non-volatile main memory (NVMM) is storage inside Non-Volatile Main Memory chips[17] (Re-RAM) – NVDIMM-P, specifications to be released 2018.[18][19][20]
Specifications
Specification (March 2007)[21] | 2.5" HDD | 1" microdrive | Flash memory | Optical disc | Tape | MRAM |
---|---|---|---|---|---|---|
Device model | Hitachi Travelstar 5k160[22] | Hitachi Microdrive 3k8[23] | Hynix HY27UH08AG5M[24] | Blu-ray | HP Ultrium 960[25] | Everspin (formerly of Freescale Semiconductor) MR2A16A[26] |
Density (GBit/cm2) | 20.3 | 18.4 | 6.7 | 3.8 | 0.047 | 0.0021 |
Capacity (GByte) | 160 | 8 | 2 | 50 | 400 | 0.004 |
Price per bit (euro/GByte) | 1.5 | 9.0 | 6.0 | 1.25 | 0.075 | 35000 |
Price per unit (euro) | 110 | 87 | 14 | 635 | 2340 | 17.4 |
Price per medium (euro) (for removables) | nd | nd | nd | 40 | 30 | nd |
Data rate (Mbit/s) | 540 | 80 | 23 | 144 | 640 | 436 |
Access time (ms) (average/typical) | 11 | 12 | 0.025 | 180 | 72000 | 0.000035 |
Power consumption (W) (average) | 1.8 | 0.6 | 0.1 | 25 | 20 | 0.08 |
Form factor (h × w × d) (cm) | 0.95×7×10 | 0.5×3×4 | 0.1×1.2×2 | 4×15×19 | 2×10×10 | 0.1×1×1.8 |
References
^ Patterson, David; Hennessy, John (1971). Computer Organization and Design: The Hardware/Software Interface. Elsevier. p. 23..mw-parser-output cite.citationfont-style:inherit.mw-parser-output qquotes:"""""""'""'".mw-parser-output code.cs1-codecolor:inherit;background:inherit;border:inherit;padding:inherit.mw-parser-output .cs1-lock-free abackground:url("//upload.wikimedia.org/wikipedia/commons/thumb/6/65/Lock-green.svg/9px-Lock-green.svg.png")no-repeat;background-position:right .1em center.mw-parser-output .cs1-lock-limited a,.mw-parser-output .cs1-lock-registration abackground:url("//upload.wikimedia.org/wikipedia/commons/thumb/d/d6/Lock-gray-alt-2.svg/9px-Lock-gray-alt-2.svg.png")no-repeat;background-position:right .1em center.mw-parser-output .cs1-lock-subscription abackground:url("//upload.wikimedia.org/wikipedia/commons/thumb/a/aa/Lock-red-alt-2.svg/9px-Lock-red-alt-2.svg.png")no-repeat;background-position:right .1em center.mw-parser-output .cs1-subscription,.mw-parser-output .cs1-registrationcolor:#555.mw-parser-output .cs1-subscription span,.mw-parser-output .cs1-registration spanborder-bottom:1px dotted;cursor:help.mw-parser-output .cs1-hidden-errordisplay:none;font-size:100%.mw-parser-output .cs1-visible-errorfont-size:100%.mw-parser-output .cs1-subscription,.mw-parser-output .cs1-registration,.mw-parser-output .cs1-formatfont-size:95%.mw-parser-output .cs1-kern-left,.mw-parser-output .cs1-kern-wl-leftpadding-left:0.2em.mw-parser-output .cs1-kern-right,.mw-parser-output .cs1-kern-wl-rightpadding-right:0.2em
^ "A Survey of Software Techniques for Using Non-Volatile Memories for Storage and Main Memory Systems", IEEE Transactions on Parallel and Distributed Systems, 2015, archived from the original on 8 January 2016
^ "i-NVMM: Securing non-volatile memory on the fly". Techrepublic. Archived from the original on 22 March 2017. Retrieved 21 March 2017.
^ "Non-Volatile Memory (NVM)". Techopedia. Archived from the original on 22 March 2017. Retrieved 21 March 2017.
^ ab By Russell Kay, ComputerWorld. "Flash memory Archived 10 June 2010 at the Wayback Machine.." 7 June 2010.
^ F-RAM Memory Technology, Ramtron.com, archived from the original on 27 January 2012, retrieved 30 January 2012
^ ab The Emergence of Practical MRAM "Archived copy" (PDF). Archived from the original (PDF) on 27 April 2011. Retrieved 20 July 2009.CS1 maint: Archived copy as title (link)
^ [1] Archived 19 January 2012 at the Wayback Machine.
^ "What is tape drive? - Definition from WhatIs.com". SearchStorage. Archived from the original on 7 July 2015. Retrieved 7 July 2015.
^ "Tape Drives". snia.org. Archived from the original on 7 July 2015. Retrieved 7 July 2015.
^ "What is hard drive?". computerhope.com. Archived from the original on 8 July 2015. Retrieved 7 July 2015.
^ "IBM 2314 Disk Drives". ncl.ac.uk. Archived from the original on 2 October 2015. Retrieved 7 July 2015.
^ "Optical Blu-ray Jukeboxes and Libraries Systems for Archiving Storage - Kintronics". kintronics.com. Archived from the original on 20 July 2015. Retrieved 7 July 2015.
^ Thinfilm and InkTec awarded IDTechEx' Technical Development Manufacturing Award IDTechEx, 15 April 2009
^ PolyIC, ThinFilm announce pilot of volume printed plastic memories Archived 29 September 2012 at the Wayback Machine. EETimes, 22 September 2009
^ All set for high-volume production of printed memories Archived 13 April 2010 at the Wayback Machine. Printed Electronics World, 12 April 2010
^ Security Vulnerabilities of Emerging Nonvolatile Main Memories and Countermeasures Archived 5 April 2017 at the Wayback Machine. -IEEE
^ "JEDEC DDR5 & NVDIMM-P Standards Under Development – JEDEC". Archived from the original on 2 December 2017.
^ 23:58, 2 Apr 2017 at; tweet_btn(), Simon Sharwood. "DDR5 to jump off the drawing board in 2018". Archived from the original on 5 April 2017.
^ "NVDIMM – Changes are Here, So What's Next?" (PDF). snia.org. SINA. Retrieved 24 April 2018.
^ Informationstoragecourse2007, BluWiki, 13 July 2009, archived from the original on 13 March 2012, retrieved 30 January 2012
^ [2] Archived 27 September 2007 at the Wayback Machine.
^ "Archived copy" (PDF). Archived from the original (PDF) on 18 July 2011. Retrieved 3 March 2011.CS1 maint: Archived copy as title (link)
^ "Archived copy" (PDF). Archived from the original (PDF) on 24 August 2010. Retrieved 11 July 2008.CS1 maint: Archived copy as title (link)
^ "HP StorageWorks Ultrium Half-Height Tape Drives (QuickSpecs/c04284138.pdf)" (PDF). hp.com. Archived from the original (PDF) on 15 September 2012. Retrieved 7 July 2015.
^ "Archived copy" (PDF). Archived (PDF) from the original on 29 January 2007. Retrieved 18 February 2008.CS1 maint: Archived copy as title (link)
External links
Supporting filesystems in persistent memory, LWN.net, 2 September 2014, by Jonathan Corbet- Research paper about perspective usage of magnetic photoconductors in magneto-optical data storage.