Third (E), in red, of a C major chord (Play (help·info)).
First inversion C major triad. The third is the bass.
In music, the third factor of a chord is the note or pitch two scale degrees above the root or tonal center. When the third is the bass note, or lowest note, of the expressed triad, the chord is in first inversion Play (help·info).
Conventionally, the third is third in importance to the root and fifth, with the third in all primary triads (I, IV, V and i, iv, v) being either major or minor. In jazz chords and theory, the third is required due to it determining chord quality.
The third in both major and augmented chords is major (E♮ in C) and the third in both minor and diminished chords is minor (E♭ in C).
Two added chords with mixed thirds, thirds separated by octave. Play chord on left (help·info)[1]Play chord on right (help·info)
Contents
1Tenth
2See also
3Notes
4References
Tenth
Major tenth on C. Play (help·info)
Minor tenth on C. Play (help·info)
In music and music theory, a tenth is the note ten scale degrees from the root of a chord and also the interval between the root and the tenth.
Since there are only seven degrees in a diatonic scale the tenth degree is the same as the mediant and the interval of a tenth is a compound third.
Duckworth, William (2007). A creative approach to music fundamentals: Includes keyboard and guitar insert (ninth ed.). 2005928009: Thomson Schirmer. pp. 1–384. ISBN 0-495-09093-X.
Kostka, Stefan; Payne, Dorothy; Almén, Byron (2013). Tonal harmony with an introduction to twentieth-century music (seventh ed.). New York: McGraw-Hill. ISBN 978-0-07-131828-0.
Persichetti, Vincent (1961). Twentieth-century harmony: Creative aspects and practice. New York: W. W. Norton. ISBN 0-393-09539-8. OCLC 398434.
v
t
e
Chord factors
Root
Third
Fifth
Seventh
Ninth
Eleventh
Thirteenth
Fifteenth
(Bass note)
v
t
e
Intervals
Numbers in brackets are the number of semitones in the interval. Fractional semitones are approximate.
Clash Royale CLAN TAG #URR8PPP up vote 1 down vote favorite I'm using WordPress 4.9.8, CiviCRM to 5.5.1, I usually send email to contact by Search> Find contacts View contact details Action> Send email Send email ok, Contact received mail ok like picture But status only Email sent though contact read email or not. So, can CiviCRM can change status to Email read when contact read email? wordpress email share | improve this question asked Sep 26 at 0:12 ToanLuong 49 9 add a comment  | up vote 1 down vote favorite I'm using WordPress 4.9.8, CiviCRM to 5.5.1, I usually send email to contact by Search> Find contacts View contact details Action> Send email Send email ok, Contact received mail ok like picture But status only Email sent though contact read email or not. So, can CiviCRM can change status to Email read when contact read email? wordpress email share | improve this questi...
Clash Royale CLAN TAG #URR8PPP up vote 2 down vote favorite I am currently learning reverse engineering and am studying the flags register. I had in my mind that rflags was just another name for one of the 16 general purpose registers, for example rax or rbx . But it looks like rflags is actually an additional register. So that makes 17 registers in total... how many more could there be? I have spent at least an hour on this and found numerous different answers. The best answer so far is this, which says that there are 40 registers in total. 16 General Purpose Registers 2 Status Registers 6 Code Segment Registers 16 SSE Registers 8 FPU/MMX Registers But if I add that up, I get 48. Could anybody provide an official answer on how many registers an x86_64 CPU has (e.g. an Intel i7). Additionally, I have seen references to 'hardware' and 'architectural' registers. What are those registers and how many are there? register x86-64 share | improve this...
Clash Royale CLAN TAG #URR8PPP 1 How can I extract a single band from multi-band raster in QGIS? I have an remote sensed image which has 6 bands (including NDVI band), I want to display each band separately, but have no idea how to do. I have seen some questions similar here but none worked for me. The original image (has 6 bands) is: I want to display the band 6 which should be like this: But I tried gdal_translate, and couldn't get the correct result. What I have got is: qgis raster multi-band share | improve this question edited Mar 5 at 0:53 Summer asked Mar 4 at 6:42 Summer Summer 23 6 Is this any help gis.stackexchange.com/questions/220658/… ? if not gis.stackexchange.com/questions/62133/… might help. – Michael Stimson Mar 4 at 6:46 Thanks for answering but when I used gdal_translate, qgis showed that 'Error 4: Kayena.tif: No such file or directory". Would you know how to fi...