mjhjmtu

Part of a series of articles about
Electromagnetism
Electricity Magnetism
Electrostatics Conductor Coulomb's law Electric charge Electric dipole moment Electric field Electric flux / potential energy Electrostatic discharge Gauss's law Induction Insulator Polarization density Static electricity Triboelectricity
Magnetostatics Ampère's law Biot–Savart law Gauss's law for magnetism Magnetic field Magnetic flux Magnetic dipole moment Magnetization Magnetomotive force
Electrodynamics Lorentz force law Electromagnetic induction Faraday's law Lenz's law Displacement current Magnetic potential Maxwell's equations Electromagnetic field Electromagnetic pulse Electromagnetic radiation Maxwell tensor Poynting vector Liénard–Wiechert potential Jefimenko's equations Eddy current London equations Mathematical descriptions of the electromagnetic field
Electrical network Alternating current Capacitance Direct current Electric current Electric potential Electromotive force Impedance Inductance Ohm's law Parallel circuit Resistance Resonant cavities Series circuit Voltage Waveguides
Covariant formulation Electromagnetic tensor (stress–energy tensor) Four-current Electromagnetic four-potential
Scientists Ampère Coulomb Faraday Gauss Heaviside Henry Hertz Lorentz Maxwell Ørsted Tesla Volta Weber
v t e

The electric dipole moment is a measure of the separation of positive and negative electrical charges within a system, that is, a measure of the system's overall polarity. The SI units for electric dipole moment are coulomb-meter (C.m); however, the most common unit is the debye (D).^{[citation needed]}

Theoretically, an electric dipole is defined by the first-order term of the multipole expansion; it consists of two equal and opposite charges that are infinitely close together. This is unrealistic, as real dipoles have separated charge.^[1] However, because the charge separation is very small compared to everyday lengths, the error introduced by treating real dipoles like they are theoretically perfect is usually negligible. The dipole's direction usually points from the negative charge towards the positive charge.

Elementary definition

Quantities defining the electric dipole moment of two point charges.

Animation showing the electric field of an electric dipole. The dipole consists of two point electric charges of opposite polarity located close together. A transformation from a point-shaped dipole to a finite-size electric dipole is shown.

A molecule of water is polar because of the unequal sharing of its electrons in a "bent" structure. A separation of charge is present with negative charge in the middle (red shade), and positive charge at the ends (blue shade).

Often in physics the dimensions of a massive object can be ignored and can be treated as a pointlike object, i.e. a point particle. Point particles with electric charge are referred to as point charges. Two point charges, one with charge +q and the other one with charge −q separated by a distance d, constitute an electric dipole (a simple case of an electric multipole). For this case, the electric dipole moment has a magnitude

p=qddisplaystyle p=qd

and is directed from the negative charge to the positive one. Some authors may split d in half and use s = d/2 since this quantity is the distance between either charge and the center of the dipole, leading to a factor of two in the definition.

A stronger mathematical definition is to use vector algebra, since a quantity with magnitude and direction, like the dipole moment of two point charges, can be expressed in vector form

p=qddisplaystyle mathbf p =qmathbf d

where d is the displacement vector pointing from the negative charge to the positive charge. The electric dipole moment vector p also points from the negative charge to the positive charge.

An idealization of this two-charge system is the electrical point dipole consisting of two (infinite) charges only infinitesimally separated, but with a finite p.

This quantity is used in the definition of polarization density.

Torque

Electric dipole p and its torque τ in a uniform E field.

An object with an electric dipole moment is subject to a torque τ when placed in an external electric field. The torque tends to align the dipole with the field. A dipole aligned parallel to an electric field has lower potential energy than a dipole making some angle with it. For a spatially uniform electric field E, the torque is given by:^[2]

τ=p×E ,displaystyle boldsymbol tau =mathbf p times mathbf E ,

where p is the dipole moment, and the symbol "×" refers to the vector cross product. The field vector and the dipole vector define a plane, and the torque is directed normal to that plane with the direction given by the right-hand rule.

A dipole oriented co- or anti-parallel to the direction in which a non-uniform electric field is increasing (gradient of the field) will experience a torque, as well as a force in the direction of its dipole moment. It can be shown that this force will always be parallel to the dipole moment regardless of co- or anti-parallel orientation of the dipole.

Expression (general case)

More generally, for a continuous distribution of charge confined to a volume V, the corresponding expression for the dipole moment is:

p(r)=∫Vρ(r0)(r0−r) d3r0,displaystyle mathbf p (mathbf r )=int limits _Vrho (mathbf r _0),left(mathbf r _0-mathbf r right) d^3mathbf r _0,

where r locates the point of observation and d³r₀ denotes an elementary volume in V. For an array of point charges, the charge density becomes a sum of Dirac delta functions:

ρ(r)=∑i=1Nqiδ(r−ri),displaystyle rho (mathbf r )=sum _i=1^N,q_i,delta left(mathbf r -mathbf r _iright),

where each r_i is a vector from some reference point to the charge q_i. Substitution into the above integration formula provides:

p(r)=∑i=1Nqi∫Vδ(r0−ri)(r0−r) d3r0=∑i=1Nqi(ri−r).displaystyle mathbf p (mathbf r )=sum _i=1^N,q_iint limits _Vdelta left(mathbf r _0-mathbf r _iright),left(mathbf r _0-mathbf r right) d^3mathbf r _0=sum _i=1^N,q_ileft(mathbf r _i-mathbf r right).

This expression is equivalent to the previous expression in the case of charge neutrality and N = 2. For two opposite charges, denoting the location of the positive charge of the pair as r₊ and the location of the negative charge as r₋ :

p(r)=q1(r1−r)+q2(r2−r)=q(r+−r)−q(r−−r)=q(r+−r−)=qd,displaystyle mathbf p (mathbf r )=q_1(mathbf r _1-mathbf r )+q_2(mathbf r _2-mathbf r )=q(mathbf r _+-mathbf r )-q(mathbf r _--mathbf r )=q(mathbf r _+-mathbf r _-)=qmathbf d ,

showing that the dipole moment vector is directed from the negative charge to the positive charge because the position vector of a point is directed outward from the origin to that point.

The dipole moment is particularly useful in the context of an overall neutral system of charges, for example a pair of opposite charges, or a neutral conductor in a uniform electric field.
For such a system of charges, visualized as an array of paired opposite charges, the relation for electric dipole moment is:

p(r)=∑i=1N∫Vqi[δ(r0−(ri+di))−δ(r0−ri)](r0−r) d3r0=∑i=1Nqi[ri+di−r−(ri−r)]=∑i=1Nqidi=∑i=1Npi ,displaystyle beginalignedmathbf p (mathbf r )&=sum _i=1^N,int limits _Vq_ileft[delta left(mathbf r _0-left(mathbf r _i+mathbf d _iright)right)-delta left(mathbf r _0-mathbf r _iright)right],left(mathbf r _0-mathbf r right) d^3mathbf r _0\&=sum _i=1^N,q_i,left[mathbf r _i+mathbf d _i-mathbf r -left(mathbf r _i-mathbf r right)right]\&=sum _i=1^Nq_imathbf d _i=sum _i=1^Nmathbf p _i ,endaligned

where r is the point of observation, and d_i = r_i − r'_i, r_i being the position of the positive charge in the dipole i, and r'_i the position of the negative charge.
This is the vector sum of the individual dipole moments of the neutral charge pairs. (Because of overall charge neutrality, the dipole moment is independent of the observer's position r.) Thus, the value of p is independent of the choice of reference point, provided the overall charge of the system is zero.

When discussing the dipole moment of a non-neutral system, such as the dipole moment of the proton, a dependence on the choice of reference point arises. In such cases it is conventional to choose the reference point to be the center of mass of the system, not some arbitrary origin.^[3] This choice is not only a matter of convention: the notion of dipole moment is essentially derived from the mechanical notion of torque, and as in mechanics, it is computationally and theoretically useful to choose the center of mass as the observation point. For a charged molecule the center of charge should be the reference point instead of the center of mass. For neutral systems the references point is not important. The dipole moment is an intrinsic property of the system.

Potential and field of an electric dipole

An electric dipole potential map. Negative potentials are in blue; positive potentials, in red.

An ideal dipole consists of two opposite charges with infinitesimal separation. The potential and field of such an ideal dipole are found next as a limiting case of an example of two opposite charges at non-zero separation.

Two closely spaced opposite charges have a potential of the form:

ϕ(r)=q4πε0|r−r+|−q4πε0|r−r−| ,displaystyle phi (mathbf r )=frac q-frac q4pi varepsilon _0left ,

with charge separation, d, defined as

d=r+−r− ,displaystyle mathbf d =mathbf r _+-mathbf r _- ,

The position relative to their center of mass (assuming equal masses), R, and the unit vector in the direction of R are given by:

R=r−r++r−2,R^=RR ,displaystyle mathbf R =mathbf r -frac mathbf r _++mathbf r _-2,quad hat mathbf R =frac mathbf R R ,

Taylor expansion in d/R (see multipole expansion and quadrupole) allows this potential to be expressed as a series.^[4][5]

ϕ(R)=14πε0qd⋅R^R2+O(d2R2)≈14πε0p⋅R^R2 ,displaystyle phi (mathbf R )=frac 14pi varepsilon _0frac qmathbf d cdot hat mathbf R R^2+Oleft(frac d^2R^2right)approx frac 14pi varepsilon _0frac mathbf p cdot hat mathbf R R^2 ,

where higher order terms in the series are vanishing at large distances, R, compared to d.^[6] Here, the electric dipole moment p is, as above:

p=qd .displaystyle mathbf p =qmathbf d .

The result for the dipole potential also can be expressed as:^[7]

ϕ(R)=−p⋅∇14πε0R ,displaystyle phi (mathbf R )=-mathbf p cdot mathbf nabla frac 14pi varepsilon _0R ,

which relates the dipole potential to that of a point charge. A key point is that the potential of the dipole falls off faster with distance R than that of the point charge.

The electric field of the dipole is the negative gradient of the potential, leading to:^[7]

E(R)=3(p⋅R^)R^−p4πε0R3 .displaystyle mathbf E left(mathbf R right)=frac 3left(mathbf p cdot hat mathbf R right)hat mathbf R -mathbf p 4pi varepsilon _0R^3 .

Thus, although two closely spaced opposite charges are not quite an ideal electric dipole (because their potential at short distances is not that of a dipole), at distances much larger than their separation, their dipole moment p appears directly in their potential and field.

As the two charges are brought closer together (d is made smaller), the dipole term in the multipole expansion based on the ratio d/R becomes the only significant term at ever closer distances R, and in the limit of infinitesimal separation the dipole term in this expansion is all that matters. As d is made infinitesimal, however, the dipole charge must be made to increase to hold p constant. This limiting process results in a "point dipole".

Dipole moment density and polarization density

The dipole moment of an array of charges,

p=∑i=1N qidi ,displaystyle mathbf p =sum _i=1^N q_imathbf d_i ,

determines the degree of polarity of the array, but for a neutral array it is simply a vector property of the array with no information about the array's absolute location. The dipole moment density of the array p(r) contains both the location of the array and its dipole moment. When it comes time to calculate the electric field in some region containing the array, Maxwell's equations are solved, and the information about the charge array is contained in the polarization density P(r) of Maxwell's equations. Depending upon how fine-grained an assessment of the electric field is required, more or less information about the charge array will have to be expressed by P(r). As explained below, sometimes it is sufficiently accurate to take P(r) = p(r). Sometimes a more detailed description is needed (for example, supplementing the dipole moment density with an additional quadrupole density) and sometimes even more elaborate versions of P(r) are necessary.

It now is explored just in what way the polarization density P(r) that enters Maxwell's equations is related to the dipole moment p of an overall neutral array of charges, and also to the dipole moment density p(r) (which describes not only the dipole moment, but also the array location). Only static situations are considered in what follows, so P(r) has no time dependence, and there is no displacement current. First is some discussion of the polarization density P(r). That discussion is followed with several particular examples.

A formulation of Maxwell's equations based upon division of charges and currents into "free" and "bound" charges and currents leads to introduction of the D- and P-fields:

D=ε0E+P ,displaystyle mathbf D =varepsilon _0mathbf E +mathbf P ,

where P is called the polarization density. In this formulation, the divergence of this equation yields:

∇⋅D=ρf=ε0∇⋅E+∇⋅P ,displaystyle nabla cdot mathbf D =rho _f=varepsilon _0nabla cdot mathbf E +nabla cdot mathbf P ,

and as the divergence term in E is the total charge, and ρ_f is "free charge", we are left with the relation:

∇⋅P=−ρb ,displaystyle nabla cdot mathbf P =-rho _b ,

with ρ_b as the bound charge, by which is meant the difference between the total and the free charge densities.

As an aside, in the absence of magnetic effects, Maxwell's equations specify that

∇×E=0 ,displaystyle nabla times mathbf E =boldsymbol 0 ,

which implies

∇×(D−P)=0 ,displaystyle nabla times left(mathbf D -mathbf P right)=boldsymbol 0 ,

Applying Helmholtz decomposition:^[8]

D−P=−∇φ ,displaystyle mathbf D-P=-nabla varphi ,

for some scalar potential φ, and:

∇⋅(D−P)=ε0∇⋅E=ρf+ρb=−∇2φ .displaystyle nabla cdot (mathbf D -mathbf P )=varepsilon _0nabla cdot mathbf E =rho _f+rho _b=-nabla ^2varphi .

Suppose the charges are divided into free and bound, and the potential is divided into

φ=φf+φb .displaystyle varphi =varphi _f+varphi _b .

Satisfaction of the boundary conditions upon φ may be divided arbitrarily between φ_f and φ_b because only the sum φ must satisfy these conditions. It follows that P is simply proportional to the electric field due to the charges selected as bound, with boundary conditions that prove convenient.^[9][10] In particular, when no free charge is present, one possible choice is P = ε₀E.

Next is discussed how several different dipole moment descriptions of a medium relate to the polarization entering Maxwell's equations.

Medium with charge and dipole densities

As described next, a model for polarization moment density p(r) results in a polarization

P(r)=p(r)displaystyle mathbf P (mathbf r )=mathbf p (mathbf r ),

restricted to the same model. For a smoothly varying dipole moment distribution p(r), the corresponding bound charge density is simply

∇⋅p(r)=ρb,displaystyle nabla cdot mathbf p (mathbf r )=rho _b,

as we will establish shortly via integration by parts. However, if p(r) exhibits an abrupt step in dipole moment at a boundary between two regions, ∇·p(r) results in a surface charge component of bound charge. This surface charge can be treated through a surface integral, or by using discontinuity conditions at the boundary, as illustrated in the various examples below.

As a first example relating dipole moment to polarization, consider a medium made up of a continuous charge density ρ(r) and a continuous dipole moment distribution p(r).^[11] The potential at a position r is:^[12][13]

ϕ(r)=14πε0∫ρ(r0)|r−r0|d3r0 +14πε0∫p(r0)⋅(r−r0)|r−r0|3d3r0,displaystyle phi (mathbf r )=frac 14pi varepsilon _0int frac rho left(mathbf r _0right)d^3mathbf r _0 +frac 14pi varepsilon _0int frac mathbf p left(mathbf r _0right)cdot left(mathbf r -mathbf r _0right)d^3mathbf r _0,

where ρ(r) is the unpaired charge density, and p(r) is the dipole moment density.^[14] Using an identity:

∇r01|r−r0|=r−r0|r−r0|3displaystyle nabla _mathbf r _0frac 1=frac mathbf r -mathbf r _0mathbf r -mathbf r _0right

the polarization integral can be transformed:

14πε0∫p(r0)⋅(r−r0)|r−r0|3d3r0=14πε0∫p(r0)⋅∇r01|r−r0|d3r0,=14πε0∫∇r0⋅(p(r0)1|r−r0|)d3r0−14πε0∫∇r0⋅p(r0)|r−r0|d3r0,displaystyle beginaligned&frac 14pi varepsilon _0int frac mathbf p left(mathbf r _0right)cdot (mathbf r -mathbf r _0)mathbf r -mathbf r _0rightd^3mathbf r _0=frac 14pi varepsilon _0int mathbf p left(mathbf r _0right)cdot nabla _mathbf r _0frac 1d^3mathbf r _0,\=&frac 14pi varepsilon _0int nabla _mathbf r _0cdot left(mathbf p left(mathbf r _0right)frac 1right)d^3mathbf r _0-frac 14pi varepsilon _0int frac nabla _mathbf r _0cdot mathbf p left(mathbf r _0right)d^3mathbf r _0,endaligned

The first term can be transformed to an integral over the surface bounding the volume of integration, and contributes a surface charge density, discussed later. Putting this result back into the potential, and ignoring the surface charge for now:

ϕ(r)=14πε0∫ρ(r0)−∇r0⋅p(r0)|r−r0|d3r0 ,displaystyle phi (mathbf r )=frac 14pi varepsilon _0int frac rho left(mathbf r _0right)-nabla _mathbf r _0cdot mathbf p left(mathbf r _0right)d^3mathbf r _0 ,

where the volume integration extends only up to the bounding surface, and does not include this surface.

The potential is determined by the total charge, which the above shows consists of:

ρtotal(r0)=ρ(r0)−∇r0⋅p(r0) ,displaystyle rho _texttotalleft(mathbf r _0right)=rho left(mathbf r _0right)-nabla _mathbf r _0cdot mathbf p left(mathbf r _0right) ,

showing that:

−∇r0⋅p(r0)=ρb .displaystyle -nabla _mathbf r _0cdot mathbf p left(mathbf r _0right)=rho _b .

In short, the dipole moment density p(r) plays the role of the polarization density P for this medium. Notice, p(r) has a non-zero divergence equal to the bound charge density (as modeled in this approximation).

It may be noted that this approach can be extended to include all the multipoles: dipole, quadrupole, etc.^[15][16] Using the relation:

∇⋅D=ρf ,displaystyle nabla cdot mathbf D =rho _f ,

the polarization density is found to be:

P(r)=pdip−∇⋅pquad+… ,displaystyle mathbf P (mathbf r )=mathbf p _textdip-nabla cdot mathbf p _textquad+ldots ,

where the added terms are meant to indicate contributions from higher multipoles. Evidently, inclusion of higher multipoles signifies that the polarization density P no longer is determined by a dipole moment density p alone. For example, in considering scattering from a charge array, different multipoles scatter an electromagnetic wave differently and independently, requiring a representation of the charges that goes beyond the dipole approximation.^[17]

Surface charge

A uniform array of identical dipoles is equivalent to a surface charge.

Above, discussion was deferred for the first term in the expression for the potential due to the dipoles. Integrating the divergence results in a surface charge. The figure at the right provides an intuitive idea of why a surface charge arises. The figure shows a uniform array of identical dipoles between two surfaces. Internally, the heads and tails of dipoles are adjacent and cancel. At the bounding surfaces, however, no cancellation occurs. Instead, on one surface the dipole heads create a positive surface charge, while at the opposite surface the dipole tails create a negative surface charge. These two opposite surface charges create a net electric field in a direction opposite to the direction of the dipoles.

This idea is given mathematical form using the potential expression above. The potential is:

ϕ(r)=14πε0∫∇r0⋅(p(r0)1|r−r0|)d3r0−14πε0∫∇r0⋅p(r0)|r−r0|d3r0 .displaystyle phi left(mathbf r right)=frac 14pi varepsilon _0int nabla _mathbf r _0cdot left(mathbf p left(mathbf r _0right)frac 1right)d^3mathbf r _0-frac 14pi varepsilon _0int frac nabla _mathbf r _0cdot mathbf p left(mathbf r _0right)d^3mathbf r _0 .

Using the divergence theorem, the divergence term transforms into the surface integral:

14πε0∫∇r0⋅(p(r0)1|r−r0|)d3r0=14πε0∫p(r0)⋅dA0|r−r0| ,displaystyle beginaligned&frac 14pi varepsilon _0int nabla _mathbf r _0cdot left(mathbf p left(mathbf r _0right)frac 1right)d^3mathbf r _0\=&frac 14pi varepsilon _0int frac mathbf p left(mathbf r _0right)cdot dmathbf A _0 ,endaligned

with dA₀ an element of surface area of the volume. In the event that p(r) is a constant, only the surface term survives:

ϕ(r)=14πε0∫1|r−r0| p⋅dA0 ,displaystyle phi (mathbf r )=frac 14pi varepsilon _0int frac 1 mathbf p cdot dmathbf A _0 ,

with dA₀ an elementary area of the surface bounding the charges. In words, the potential due to a constant p inside the surface is equivalent to that of a surface charge

σ=p⋅dAdisplaystyle sigma =mathbf p cdot dmathbf A

which is positive for surface elements with a component in the direction of p and negative for surface elements pointed oppositely. (Usually the direction of a surface element is taken to be that of the outward normal to the surface at the location of the element.)

If the bounding surface is a sphere, and the point of observation is at the center of this sphere, the integration over the surface of the sphere is zero: the positive and negative surface charge contributions to the potential cancel. If the point of observation is off-center, however, a net potential can result (depending upon the situation) because the positive and negative charges are at different distances from the point of observation.^[18] The field due to the surface charge is:

E(r)=−14πε0∇r∫1|r−r0| p⋅dA0 ,displaystyle mathbf E left(mathbf r right)=-frac 14pi varepsilon _0nabla _mathbf r int frac 1 mathbf p cdot dmathbf A _0 ,

which, at the center of a spherical bounding surface is not zero (the fields of negative and positive charges on opposite sides of the center add because both fields point the same way) but is instead:^[19]

E=−p3ε0 .displaystyle mathbf E =-frac mathbf p 3varepsilon _0 .

If we suppose the polarization of the dipoles was induced by an external field, the polarization field opposes the applied field and sometimes is called a depolarization field.^[20][21] In the case when the polarization is outside a spherical cavity, the field in the cavity due to the surrounding dipoles is in the same direction as the polarization.^[22]

In particular, if the electric susceptibility is introduced through the approximation:

p(r)=ε0χ(r)E(r) ,displaystyle mathbf p (mathbf r )=varepsilon _0chi (mathbf r )mathbf E (mathbf r ) ,

where E, in this case and in the following, represent the external field which induces the polarization.

Then:

∇⋅p(r)=∇⋅(χ(r)ε0E(r))=−ρb .displaystyle nabla cdot mathbf p (mathbf r )=nabla cdot left(chi (mathbf r )varepsilon _0mathbf E (mathbf r )right)=-rho _b .

Whenever χ(r) is used to model a step discontinuity at the boundary between two regions, the step produces a surface charge layer. For example, integrating along a normal to the bounding surface from a point just interior to one surface to another point just exterior:

ε0n^⋅[χ(r+)E(r+)−χ(r−)E(r−)]=1An∫dΩn ρb=0 ,displaystyle varepsilon _0hat mathbf n cdot left[chi left(mathbf r _+right)mathbf E left(mathbf r _+right)-chi left(mathbf r _-right)mathbf E left(mathbf r _-right)right]=frac 1A_nint dOmega _n rho _b=0 ,

where A_n, Ω_n indicate the area and volume of an elementary region straddling the boundary between the regions, and n^displaystyle hat mathbf n a unit normal to the surface. The right side vanishes as the volume shrinks, inasmuch as ρ_b is finite, indicating a discontinuity in E, and therefore a surface charge. That is, where the modeled medium includes a step in permittivity, the polarization density corresponding to the dipole moment density

p(r)=χ(r)E(r)displaystyle mathbf p (mathbf r )=chi (mathbf r )mathbf E (mathbf r )

necessarily includes the contribution of a surface charge.^[23][24][25]

A physically more realistic modeling of p(r) would have the dipole moment density drop off rapidly, but smoothly to zero at the boundary of the confining region, rather than making a sudden step to zero density. Then the surface charge will not concentrate in an infinitely thin surface, but instead, being the divergence of a smoothly varying dipole moment density, will distribute itself throughout a thin, but finite transition layer.

Dielectric sphere in uniform external electric field

Field lines of the D-field in a dielectric sphere with greater susceptibility than its surroundings, placed in a previously-uniform field.^[26] The field lines of the E-field (not shown) coincide everywhere with those of the D-field, but inside the sphere, their density is lower, corresponding to the fact that the E-field is weaker inside the sphere than outside. Many of the external E-field lines terminate on the surface of the sphere, where there is a bound charge.

The above general remarks about surface charge are made more concrete by considering the example of a dielectric sphere in a uniform electric field.^[27][28] The sphere is found to adopt a surface charge related to the dipole moment of its interior.

A uniform external electric field is supposed to point in the z-direction, and spherical-polar coordinates are introduced so the potential created by this field is:

ϕ∞=−E∞z=−E∞rcos⁡θ .displaystyle phi _infty =-E_infty z=-E_infty rcos theta .

The sphere is assumed to be described by a dielectric constant κ, that is,

D=κϵ0E ,displaystyle mathbf D =kappa epsilon _0mathbf E ,

and inside the sphere the potential satisfies Laplace's equation. Skipping a few details, the solution inside the sphere is:

ϕ<=Arcos⁡θ ,displaystyle phi _<=Arcos theta ,

while outside the sphere:

ϕ>=(Br+Cr2)cos⁡θ .displaystyle phi _>=left(Br+frac Cr^2right)cos theta .

At large distances, φ_> → φ_∞ so B = −E_∞ . Continuity of potential and of the radial component of displacement D = κε₀E determine the other two constants. Supposing the radius of the sphere is R,

A=−3κ+2E∞ ; C=κ−1κ+2E∞R3 ,displaystyle A=-frac 3kappa +2E_infty ; C=frac kappa -1kappa +2E_infty R^3 ,

As a consequence, the potential is:

ϕ>=(−r+κ−1κ+2R3r2)E∞cos⁡θ ,displaystyle phi _>=left(-r+frac kappa -1kappa +2frac R^3r^2right)E_infty cos theta ,

which is the potential due to applied field and, in addition, a dipole in the direction of the applied field (the z-direction) of dipole moment:

p=4πε0(κ−1κ+2R3)E∞ ,displaystyle mathbf p =4pi varepsilon _0left(frac kappa -1kappa +2R^3right)mathbf E _infty ,

or, per unit volume:

pV=3ε0(κ−1κ+2)E∞ .displaystyle frac mathbf p V=3varepsilon _0left(frac kappa -1kappa +2right)mathbf E _infty .

The factor (κ − 1)/(κ + 2) is called the Clausius–Mossotti factor and shows that the induced polarization flips sign if κ < 1. Of course, this cannot happen in this example, but in an example with two different dielectrics κ is replaced by the ratio of the inner to outer region dielectric constants, which can be greater or smaller than one. The potential inside the sphere is:

ϕ<=−3κ+2E∞rcos⁡θ ,displaystyle phi _<=-frac 3kappa +2E_infty rcos theta ,

leading to the field inside the sphere:

−∇ϕ<=3κ+2E∞=(1−κ−1κ+2)E∞ ,displaystyle -nabla phi _<=frac 3kappa +2mathbf E _infty =left(1-frac kappa -1kappa +2right)mathbf E _infty ,

showing the depolarizing effect of the dipole. Notice that the field inside the sphere is uniform and parallel to the applied field. The dipole moment is uniform throughout the interior of the sphere. The surface charge density on the sphere is the difference between the radial field components:

σ=3ε0κ−1κ+2E∞cos⁡θ=1Vp⋅R^ .displaystyle sigma =3varepsilon _0frac kappa -1kappa +2E_infty cos theta =frac 1Vmathbf p cdot hat mathbf R .

This linear dielectric example shows that the dielectric constant treatment is equivalent to the uniform dipole moment model and leads to zero charge everywhere except for the surface charge at the boundary of the sphere.

General media

If observation is confined to regions sufficiently remote from a system of charges, a multipole expansion of the exact polarization density can be made. By truncating this expansion (for example, retaining only the dipole terms, or only the dipole and quadrupole terms, or etc.), the results of the previous section are regained. In particular, truncating the expansion at the dipole term, the result is indistinguishable from the polarization density generated by a uniform dipole moment confined to the charge region. To the accuracy of this dipole approximation, as shown in the previous section, the dipole moment density p(r) (which includes not only p but the location of p) serves as P(r).

At locations inside the charge array, to connect an array of paired charges to an approximation involving only a dipole moment density p(r) requires additional considerations. The simplest approximation is to replace the charge array with a model of ideal (infinitesimally spaced) dipoles. In particular, as in the example above that uses a constant dipole moment density confined to a finite region, a surface charge and depolarization field results. A more general version of this model (which allows the polarization to vary with position) is the customary approach using electric susceptibility or electrical permittivity.

A more complex model of the point charge array introduces an effective medium by averaging the microscopic charges;^[21] for example, the averaging can arrange that only dipole fields play a role.^[29][30] A related approach is to divide the charges into those nearby the point of observation, and those far enough away to allow a multipole expansion. The nearby charges then give rise to local field effects.^[19][31] In a common model of this type, the distant charges are treated as a homogeneous medium using a dielectric constant, and the nearby charges are treated only in a dipole approximation.^[32] The approximation of a medium or an array of charges by only dipoles and their associated dipole moment density is sometimes called the point dipole approximation, the discrete dipole approximation, or simply the dipole approximation.^[33][34][35]

Electric dipole moments of fundamental particles

Not to be confused with spin which refers to the magnetic dipole moments of particles, much experimental work is continuing on measuring the electric dipole moments (EDM) of fundamental and composite particles, namely those of the electron and neutron, respectively. As EDMs violate both the parity (P) and time-reversal (T) symmetries, their values yield a mostly model-independent measure of CP-violation in nature (assuming CPT symmetry is valid).^[36] Therefore, values for these EDMs place strong constraints upon the scale of CP-violation that extensions to the standard model of particle physics may allow. Current generations of experiments are designed to be sensitive to the supersymmetry range of EDMs, providing complementary experiments to those done at the LHC.^[37]

Indeed, many theories are inconsistent with the current limits and have effectively been ruled out, and established theory permits a much larger value than these limits, leading to the strong CP problem and prompting searches for new particles such as the axion.^[38]

Dipole moments of molecules

Dipole moments in molecules are responsible for the behavior of a substance in the presence of external electric fields. The dipoles tend to be aligned to the external field which can be constant or time-dependent. This effect forms the basis of a modern experimental technique called dielectric spectroscopy.

Dipole moments can be found in common molecules such as water and also in biomolecules such as proteins.^[39]

By means of the total dipole moment of some material one can compute the dielectric constant which is related to the more intuitive concept of conductivity. If MTotdisplaystyle mathcal M_rm Tot, is the total dipole moment of the sample, then the dielectric
constant is given by,

ϵ=1+k⟨MTot2⟩displaystyle epsilon =1+kleftlangle mathcal M_textTot^2rightrangle

where k is a constant and ⟨MTot2⟩=⟨MTot(t=0)MTot(t=0)⟩displaystyle leftlangle mathcal M_textTot^2rightrangle =leftlangle mathcal M_textTot(t=0)mathcal M_textTot(t=0)rightrangle is the time correlation function of the total dipole moment. In general the total dipole moment have contributions coming
from translations and rotations of the molecules in the sample,

MTot=MTrans+MRot.displaystyle mathcal M_textTot=mathcal M_textTrans+mathcal M_textRot.

Therefore, the dielectric constant (and the conductivity) has contributions from both terms. This approach can be generalized to compute the frequency dependent dielectric function.^[40]

It is possible to calculate dipole moments from electronic structure theory, either as a response to constant electric fields or from the density matrix.^[41] Such values however are not directly comparable to experiment due to the potential presence of nuclear quantum effects, which can be substantial for even simple systems like the ammonia molecule.^[42]Coupled cluster theory (especially CCSD(T)^[43]) can give very accurate dipole moments,^[44] although it is possible to get reasonable estimates (within about 5%) from density functional theory, especially if hybrid or double hybrid functionals are employed.^[45] The dipole moment of a molecule can also be calculated based on the molecular structure using the concept of group contribution methods.^[46]

See also

References and in-line notes

Further reading

• 
  Melvin Schwartz (1987). "Electrical DIPOLE MOMENT". Principles of Electrodynamics (reprint of 1972 ed.). Courier Dover Publications. p. 49ff. ISBN 978-0-486-65493-5.
  

External links

• Electric Dipole Moment – from Eric Weisstein's World of Physics


• Electrostatic Dipole Multiphysics Model