What is a blind encoder?

The name of the pictureThe name of the pictureThe name of the pictureClash Royale CLAN TAG#URR8PPP











up vote
7
down vote

favorite












As I'm studying, I found that GPS has to have 5 satellites or 4 satellites with "blind encoders" to use RAIM.



What is a blind encoder and what is its purpose?










share|improve this question























  • Can you reference the source you are learning from or provide the relevant quotes from it? Because as far as I can tell, RAIM needs 5 satellites for error detection and 6 for correction and there is no way around it. Also, I am not sure what “blind-encorder” is it talking about, but there does not seem to be anything called blind encoder around GPS.
    – Jan Hudec
    Nov 18 at 18:32










  • As I know, GPS knows our altitude (via blind encoder which is another point of reference for position information. Therefore we need only 4 satellite to trilaterate our position.
    – Mun Park
    Nov 18 at 18:50










  • Closely related. I think you may be mixing some different things here: a blind encoder is usually part of an aircraft's altimeter, which has nothing to do with RAIM.
    – Pondlife
    Nov 18 at 19:08










  • Sorry for that. So could you let me know what blind encoder is how it is used in A/C?
    – Mun Park
    Nov 18 at 19:51






  • 1




    @MunPark GPS doesn't know your altitude. It knows the altitude of its satellites, but it has no idea what your altitude (or your position in any dimension) is. Your flight computers may know because of data from your altimeter(s), but the Global Positioning System doesn't know, as it's a transmit-only system that doesn't even know who is receiving its signals, let alone their altitudes.
    – reirab
    Nov 19 at 10:46














up vote
7
down vote

favorite












As I'm studying, I found that GPS has to have 5 satellites or 4 satellites with "blind encoders" to use RAIM.



What is a blind encoder and what is its purpose?










share|improve this question























  • Can you reference the source you are learning from or provide the relevant quotes from it? Because as far as I can tell, RAIM needs 5 satellites for error detection and 6 for correction and there is no way around it. Also, I am not sure what “blind-encorder” is it talking about, but there does not seem to be anything called blind encoder around GPS.
    – Jan Hudec
    Nov 18 at 18:32










  • As I know, GPS knows our altitude (via blind encoder which is another point of reference for position information. Therefore we need only 4 satellite to trilaterate our position.
    – Mun Park
    Nov 18 at 18:50










  • Closely related. I think you may be mixing some different things here: a blind encoder is usually part of an aircraft's altimeter, which has nothing to do with RAIM.
    – Pondlife
    Nov 18 at 19:08










  • Sorry for that. So could you let me know what blind encoder is how it is used in A/C?
    – Mun Park
    Nov 18 at 19:51






  • 1




    @MunPark GPS doesn't know your altitude. It knows the altitude of its satellites, but it has no idea what your altitude (or your position in any dimension) is. Your flight computers may know because of data from your altimeter(s), but the Global Positioning System doesn't know, as it's a transmit-only system that doesn't even know who is receiving its signals, let alone their altitudes.
    – reirab
    Nov 19 at 10:46












up vote
7
down vote

favorite









up vote
7
down vote

favorite











As I'm studying, I found that GPS has to have 5 satellites or 4 satellites with "blind encoders" to use RAIM.



What is a blind encoder and what is its purpose?










share|improve this question















As I'm studying, I found that GPS has to have 5 satellites or 4 satellites with "blind encoders" to use RAIM.



What is a blind encoder and what is its purpose?







gps raim






share|improve this question















share|improve this question













share|improve this question




share|improve this question








edited Nov 18 at 18:57









Pondlife

49.8k8134273




49.8k8134273










asked Nov 18 at 18:08









Mun Park

563




563











  • Can you reference the source you are learning from or provide the relevant quotes from it? Because as far as I can tell, RAIM needs 5 satellites for error detection and 6 for correction and there is no way around it. Also, I am not sure what “blind-encorder” is it talking about, but there does not seem to be anything called blind encoder around GPS.
    – Jan Hudec
    Nov 18 at 18:32










  • As I know, GPS knows our altitude (via blind encoder which is another point of reference for position information. Therefore we need only 4 satellite to trilaterate our position.
    – Mun Park
    Nov 18 at 18:50










  • Closely related. I think you may be mixing some different things here: a blind encoder is usually part of an aircraft's altimeter, which has nothing to do with RAIM.
    – Pondlife
    Nov 18 at 19:08










  • Sorry for that. So could you let me know what blind encoder is how it is used in A/C?
    – Mun Park
    Nov 18 at 19:51






  • 1




    @MunPark GPS doesn't know your altitude. It knows the altitude of its satellites, but it has no idea what your altitude (or your position in any dimension) is. Your flight computers may know because of data from your altimeter(s), but the Global Positioning System doesn't know, as it's a transmit-only system that doesn't even know who is receiving its signals, let alone their altitudes.
    – reirab
    Nov 19 at 10:46
















  • Can you reference the source you are learning from or provide the relevant quotes from it? Because as far as I can tell, RAIM needs 5 satellites for error detection and 6 for correction and there is no way around it. Also, I am not sure what “blind-encorder” is it talking about, but there does not seem to be anything called blind encoder around GPS.
    – Jan Hudec
    Nov 18 at 18:32










  • As I know, GPS knows our altitude (via blind encoder which is another point of reference for position information. Therefore we need only 4 satellite to trilaterate our position.
    – Mun Park
    Nov 18 at 18:50










  • Closely related. I think you may be mixing some different things here: a blind encoder is usually part of an aircraft's altimeter, which has nothing to do with RAIM.
    – Pondlife
    Nov 18 at 19:08










  • Sorry for that. So could you let me know what blind encoder is how it is used in A/C?
    – Mun Park
    Nov 18 at 19:51






  • 1




    @MunPark GPS doesn't know your altitude. It knows the altitude of its satellites, but it has no idea what your altitude (or your position in any dimension) is. Your flight computers may know because of data from your altimeter(s), but the Global Positioning System doesn't know, as it's a transmit-only system that doesn't even know who is receiving its signals, let alone their altitudes.
    – reirab
    Nov 19 at 10:46















Can you reference the source you are learning from or provide the relevant quotes from it? Because as far as I can tell, RAIM needs 5 satellites for error detection and 6 for correction and there is no way around it. Also, I am not sure what “blind-encorder” is it talking about, but there does not seem to be anything called blind encoder around GPS.
– Jan Hudec
Nov 18 at 18:32




Can you reference the source you are learning from or provide the relevant quotes from it? Because as far as I can tell, RAIM needs 5 satellites for error detection and 6 for correction and there is no way around it. Also, I am not sure what “blind-encorder” is it talking about, but there does not seem to be anything called blind encoder around GPS.
– Jan Hudec
Nov 18 at 18:32












As I know, GPS knows our altitude (via blind encoder which is another point of reference for position information. Therefore we need only 4 satellite to trilaterate our position.
– Mun Park
Nov 18 at 18:50




As I know, GPS knows our altitude (via blind encoder which is another point of reference for position information. Therefore we need only 4 satellite to trilaterate our position.
– Mun Park
Nov 18 at 18:50












Closely related. I think you may be mixing some different things here: a blind encoder is usually part of an aircraft's altimeter, which has nothing to do with RAIM.
– Pondlife
Nov 18 at 19:08




Closely related. I think you may be mixing some different things here: a blind encoder is usually part of an aircraft's altimeter, which has nothing to do with RAIM.
– Pondlife
Nov 18 at 19:08












Sorry for that. So could you let me know what blind encoder is how it is used in A/C?
– Mun Park
Nov 18 at 19:51




Sorry for that. So could you let me know what blind encoder is how it is used in A/C?
– Mun Park
Nov 18 at 19:51




1




1




@MunPark GPS doesn't know your altitude. It knows the altitude of its satellites, but it has no idea what your altitude (or your position in any dimension) is. Your flight computers may know because of data from your altimeter(s), but the Global Positioning System doesn't know, as it's a transmit-only system that doesn't even know who is receiving its signals, let alone their altitudes.
– reirab
Nov 19 at 10:46




@MunPark GPS doesn't know your altitude. It knows the altitude of its satellites, but it has no idea what your altitude (or your position in any dimension) is. Your flight computers may know because of data from your altimeter(s), but the Global Positioning System doesn't know, as it's a transmit-only system that doesn't even know who is receiving its signals, let alone their altitudes.
– reirab
Nov 19 at 10:46










2 Answers
2






active

oldest

votes

















up vote
19
down vote













A blind encoder is an altimeter that encodes pressure altitude and outputs it on a databus. They are "blind" in that they do not display data to the pilot. Most general aviation units use a parallel bus with Gillham encoding. More expensive units and air data computers use serial bus output, commonly ARINC 429.



Historically, the blind encoder existed to provide pressure altitude data to the transponder to enable Mode C reporting.



When it was proposed to use GPS as a primary means of navigation in the early 1990's, the FAA deemed that a means of ensuring the integrity of the signal was essential. The longer term solution was to establish WAAS which provided both augmentation and an integrity channel. The short term solution was to have the receivers include an internal monitor, which took on the name RAIM for Receiver Autonomous Integrity Monitor.



RAIM algorithms have evolved several times over the years. Since early GPS receivers were often single or 3 channel receivers, the use of altitude as a substitute for an additional satellite was common. (Altitude is just another range in the rho-rho computation.)



Later GPS receivers moved to 6 and 12 channel receivers, thus enabling RAIM algorithms that don't need altitude data except in extreme cases.



So yes, the number of satellites needed for a RAIM calculation can be reduced by one when pressure altitude is available from a blind encoder.






share|improve this answer




















  • +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
    – Pondlife
    Nov 18 at 21:49






  • 3




    The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
    – Gerry
    Nov 18 at 23:43










  • thanks for that!
    – Pondlife
    Nov 19 at 0:08










  • Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
    – Jan Hudec
    2 days ago











  • @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
    – Gerry
    2 days ago

















up vote
0
down vote













Receiver autonomous integrity monitoring
Receiver autonomous integrity monitoring (RAIM) is a technology developed to assess the integrity of global positioning system (GPS) signals in a GPS receiver system. It is of special importance in safety-critical GPS applications, such as in aviation or marine navigation



Check out the GPS article in this FAA newsletter to start with:
http://www.faa.gov/news/safety_briefing/2010/media/JanFeb2010.pdf



RAIM prediction is what is of primary concern for Non-WAAS equipped GPSs.
If you are WAAS equipped then you are good to go without doing prediction.






share|improve this answer








New contributor




KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.

















    Your Answer





    StackExchange.ifUsing("editor", function ()
    return StackExchange.using("mathjaxEditing", function ()
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
    );
    );
    , "mathjax-editing");

    StackExchange.ready(function()
    var channelOptions =
    tags: "".split(" "),
    id: "528"
    ;
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function()
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled)
    StackExchange.using("snippets", function()
    createEditor();
    );

    else
    createEditor();

    );

    function createEditor()
    StackExchange.prepareEditor(
    heartbeatType: 'answer',
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader:
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    ,
    noCode: true, onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    );



    );













     

    draft saved


    draft discarded


















    StackExchange.ready(
    function ()
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f57225%2fwhat-is-a-blind-encoder%23new-answer', 'question_page');

    );

    Post as a guest















    Required, but never shown

























    2 Answers
    2






    active

    oldest

    votes








    2 Answers
    2






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes








    up vote
    19
    down vote













    A blind encoder is an altimeter that encodes pressure altitude and outputs it on a databus. They are "blind" in that they do not display data to the pilot. Most general aviation units use a parallel bus with Gillham encoding. More expensive units and air data computers use serial bus output, commonly ARINC 429.



    Historically, the blind encoder existed to provide pressure altitude data to the transponder to enable Mode C reporting.



    When it was proposed to use GPS as a primary means of navigation in the early 1990's, the FAA deemed that a means of ensuring the integrity of the signal was essential. The longer term solution was to establish WAAS which provided both augmentation and an integrity channel. The short term solution was to have the receivers include an internal monitor, which took on the name RAIM for Receiver Autonomous Integrity Monitor.



    RAIM algorithms have evolved several times over the years. Since early GPS receivers were often single or 3 channel receivers, the use of altitude as a substitute for an additional satellite was common. (Altitude is just another range in the rho-rho computation.)



    Later GPS receivers moved to 6 and 12 channel receivers, thus enabling RAIM algorithms that don't need altitude data except in extreme cases.



    So yes, the number of satellites needed for a RAIM calculation can be reduced by one when pressure altitude is available from a blind encoder.






    share|improve this answer




















    • +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
      – Pondlife
      Nov 18 at 21:49






    • 3




      The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
      – Gerry
      Nov 18 at 23:43










    • thanks for that!
      – Pondlife
      Nov 19 at 0:08










    • Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
      – Jan Hudec
      2 days ago











    • @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
      – Gerry
      2 days ago














    up vote
    19
    down vote













    A blind encoder is an altimeter that encodes pressure altitude and outputs it on a databus. They are "blind" in that they do not display data to the pilot. Most general aviation units use a parallel bus with Gillham encoding. More expensive units and air data computers use serial bus output, commonly ARINC 429.



    Historically, the blind encoder existed to provide pressure altitude data to the transponder to enable Mode C reporting.



    When it was proposed to use GPS as a primary means of navigation in the early 1990's, the FAA deemed that a means of ensuring the integrity of the signal was essential. The longer term solution was to establish WAAS which provided both augmentation and an integrity channel. The short term solution was to have the receivers include an internal monitor, which took on the name RAIM for Receiver Autonomous Integrity Monitor.



    RAIM algorithms have evolved several times over the years. Since early GPS receivers were often single or 3 channel receivers, the use of altitude as a substitute for an additional satellite was common. (Altitude is just another range in the rho-rho computation.)



    Later GPS receivers moved to 6 and 12 channel receivers, thus enabling RAIM algorithms that don't need altitude data except in extreme cases.



    So yes, the number of satellites needed for a RAIM calculation can be reduced by one when pressure altitude is available from a blind encoder.






    share|improve this answer




















    • +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
      – Pondlife
      Nov 18 at 21:49






    • 3




      The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
      – Gerry
      Nov 18 at 23:43










    • thanks for that!
      – Pondlife
      Nov 19 at 0:08










    • Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
      – Jan Hudec
      2 days ago











    • @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
      – Gerry
      2 days ago












    up vote
    19
    down vote










    up vote
    19
    down vote









    A blind encoder is an altimeter that encodes pressure altitude and outputs it on a databus. They are "blind" in that they do not display data to the pilot. Most general aviation units use a parallel bus with Gillham encoding. More expensive units and air data computers use serial bus output, commonly ARINC 429.



    Historically, the blind encoder existed to provide pressure altitude data to the transponder to enable Mode C reporting.



    When it was proposed to use GPS as a primary means of navigation in the early 1990's, the FAA deemed that a means of ensuring the integrity of the signal was essential. The longer term solution was to establish WAAS which provided both augmentation and an integrity channel. The short term solution was to have the receivers include an internal monitor, which took on the name RAIM for Receiver Autonomous Integrity Monitor.



    RAIM algorithms have evolved several times over the years. Since early GPS receivers were often single or 3 channel receivers, the use of altitude as a substitute for an additional satellite was common. (Altitude is just another range in the rho-rho computation.)



    Later GPS receivers moved to 6 and 12 channel receivers, thus enabling RAIM algorithms that don't need altitude data except in extreme cases.



    So yes, the number of satellites needed for a RAIM calculation can be reduced by one when pressure altitude is available from a blind encoder.






    share|improve this answer












    A blind encoder is an altimeter that encodes pressure altitude and outputs it on a databus. They are "blind" in that they do not display data to the pilot. Most general aviation units use a parallel bus with Gillham encoding. More expensive units and air data computers use serial bus output, commonly ARINC 429.



    Historically, the blind encoder existed to provide pressure altitude data to the transponder to enable Mode C reporting.



    When it was proposed to use GPS as a primary means of navigation in the early 1990's, the FAA deemed that a means of ensuring the integrity of the signal was essential. The longer term solution was to establish WAAS which provided both augmentation and an integrity channel. The short term solution was to have the receivers include an internal monitor, which took on the name RAIM for Receiver Autonomous Integrity Monitor.



    RAIM algorithms have evolved several times over the years. Since early GPS receivers were often single or 3 channel receivers, the use of altitude as a substitute for an additional satellite was common. (Altitude is just another range in the rho-rho computation.)



    Later GPS receivers moved to 6 and 12 channel receivers, thus enabling RAIM algorithms that don't need altitude data except in extreme cases.



    So yes, the number of satellites needed for a RAIM calculation can be reduced by one when pressure altitude is available from a blind encoder.







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered Nov 18 at 21:01









    Gerry

    10.1k12949




    10.1k12949











    • +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
      – Pondlife
      Nov 18 at 21:49






    • 3




      The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
      – Gerry
      Nov 18 at 23:43










    • thanks for that!
      – Pondlife
      Nov 19 at 0:08










    • Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
      – Jan Hudec
      2 days ago











    • @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
      – Gerry
      2 days ago
















    • +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
      – Pondlife
      Nov 18 at 21:49






    • 3




      The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
      – Gerry
      Nov 18 at 23:43










    • thanks for that!
      – Pondlife
      Nov 19 at 0:08










    • Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
      – Jan Hudec
      2 days ago











    • @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
      – Gerry
      2 days ago















    +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
    – Pondlife
    Nov 18 at 21:49




    +1, I had no idea that there's a link between altitude encoding and RAIM. I'm not doubting your answer, but do you have any sources on the algorithms you mentioned?
    – Pondlife
    Nov 18 at 21:49




    3




    3




    The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
    – Gerry
    Nov 18 at 23:43




    The information is in the GPS MOPS, RTCA DO-229. The basics are covered in Appendix G—REQUIREMENTS FOR BAROMETRIC ALTIMETER AIDING in DO-229C. I'm not sure if the reference is still valid in the current version DO-229E. I do know that the newer version does require the use of FDE RAIM as the algorithms have evolved.
    – Gerry
    Nov 18 at 23:43












    thanks for that!
    – Pondlife
    Nov 19 at 0:08




    thanks for that!
    – Pondlife
    Nov 19 at 0:08












    Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
    – Jan Hudec
    2 days ago





    Of course the barometric altimeter reading depends on the weather, so the position obtained with use of barometric altitude has lower accuracy. Good enough for en-route navigation, but not for approaches or anything needing RNP.
    – Jan Hudec
    2 days ago













    @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
    – Gerry
    2 days ago




    @JanHudec Certainly not CAT I or APV approaches, but a TSO C129 GPS with RAIM is capable of RNP 0.3 non-precision approaches. When combined with an FMS the same GPS sensors support LNAV/VNAV approaches. They did require pilot input of the local altimeter setting. Most of those approaches had MDAs in the 250 to 400 foot range.
    – Gerry
    2 days ago










    up vote
    0
    down vote













    Receiver autonomous integrity monitoring
    Receiver autonomous integrity monitoring (RAIM) is a technology developed to assess the integrity of global positioning system (GPS) signals in a GPS receiver system. It is of special importance in safety-critical GPS applications, such as in aviation or marine navigation



    Check out the GPS article in this FAA newsletter to start with:
    http://www.faa.gov/news/safety_briefing/2010/media/JanFeb2010.pdf



    RAIM prediction is what is of primary concern for Non-WAAS equipped GPSs.
    If you are WAAS equipped then you are good to go without doing prediction.






    share|improve this answer








    New contributor




    KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
    Check out our Code of Conduct.





















      up vote
      0
      down vote













      Receiver autonomous integrity monitoring
      Receiver autonomous integrity monitoring (RAIM) is a technology developed to assess the integrity of global positioning system (GPS) signals in a GPS receiver system. It is of special importance in safety-critical GPS applications, such as in aviation or marine navigation



      Check out the GPS article in this FAA newsletter to start with:
      http://www.faa.gov/news/safety_briefing/2010/media/JanFeb2010.pdf



      RAIM prediction is what is of primary concern for Non-WAAS equipped GPSs.
      If you are WAAS equipped then you are good to go without doing prediction.






      share|improve this answer








      New contributor




      KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
      Check out our Code of Conduct.



















        up vote
        0
        down vote










        up vote
        0
        down vote









        Receiver autonomous integrity monitoring
        Receiver autonomous integrity monitoring (RAIM) is a technology developed to assess the integrity of global positioning system (GPS) signals in a GPS receiver system. It is of special importance in safety-critical GPS applications, such as in aviation or marine navigation



        Check out the GPS article in this FAA newsletter to start with:
        http://www.faa.gov/news/safety_briefing/2010/media/JanFeb2010.pdf



        RAIM prediction is what is of primary concern for Non-WAAS equipped GPSs.
        If you are WAAS equipped then you are good to go without doing prediction.






        share|improve this answer








        New contributor




        KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.









        Receiver autonomous integrity monitoring
        Receiver autonomous integrity monitoring (RAIM) is a technology developed to assess the integrity of global positioning system (GPS) signals in a GPS receiver system. It is of special importance in safety-critical GPS applications, such as in aviation or marine navigation



        Check out the GPS article in this FAA newsletter to start with:
        http://www.faa.gov/news/safety_briefing/2010/media/JanFeb2010.pdf



        RAIM prediction is what is of primary concern for Non-WAAS equipped GPSs.
        If you are WAAS equipped then you are good to go without doing prediction.







        share|improve this answer








        New contributor




        KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.









        share|improve this answer



        share|improve this answer






        New contributor




        KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.









        answered Nov 19 at 6:48









        KARTIK GURNANI

        1




        1




        New contributor




        KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.





        New contributor





        KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.






        KARTIK GURNANI is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.



























             

            draft saved


            draft discarded















































             


            draft saved


            draft discarded














            StackExchange.ready(
            function ()
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f57225%2fwhat-is-a-blind-encoder%23new-answer', 'question_page');

            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown






            Popular posts from this blog

            How to check contact read email or not when send email to Individual?

            Displaying single band from multi-band raster using QGIS

            How many registers does an x86_64 CPU actually have?