I've become an electrical conductor for my headphones… but how?

The name of the pictureThe name of the pictureThe name of the pictureClash Royale CLAN TAG#URR8PPP











up vote
25
down vote

favorite
5












So I have a pair of Bose noise-cancellation headphones that I plug into my keyboard every night to charge them (via my keyboard's USB port). My keyboard happens to be a metallic Apple keyboard. You will see why this may be important to note later.



Over time, I noticed a certain dull, electrical buzzing sound in my right earbud which occurred when I turned the noise-cancellation on. This buzzing sound was not constantly there. It would randomly appear for arbitrary periods of time and then vanish. It wasn't loud either, but it was loud enough to be noticeable and annoying.



For the longest time, I had no clue why this would happen. Sometimes the earbud would be perfectly silent (as it's supposed to be)... and then a buzzing noise would come out of nowhere. This was incredibly annoying and my only remedy was to listen to loud electronic music which blended in with the buzz and made it relatively unnoticeable. Of course, listening to almost any other kind of music proved annoying since my earbud would randomly, intermittently buzz at me.



Finally, one day, I noticed that when I touched my Android phone, the buzzing sound would increase in volume. I thought at first that this was due to my bodily position somehow stretching the wire, but with further testing I confirmed that my Android phone was the culprit. I slowly discovered that touching different objects, even when the headphones were not plugged into the speakers, would result in volume changes of this buzz.



One thing I noticed was that touching the headphone jack, whilst touching the Android phone that increased volume, would silence the buzz. With further testing, I noticed that touching my metallic keyboard would also silence the buzz, even whilst touching the Android phone or under any other circumstance in which there was a buzz.



I finally realized that my body is somehow conducting electricity when touching objects such as my Apple keyboard, headphone jack, or Android phone and that these are all related to the annoying buzz and nullification thereof. I found this bizarre and fascinating.



Ever since this discovery, I've found that I can silence this annoying buzz by pressing any of my fingertips on my metallic keyboard. This is also annoying, since it can make typing awkward to continually have one finger pressing against the metallic part. Nonetheless, I have no idea why this works at all; I suspect it might have something to do with my usage of the keyboard to charge the headphones via its USB port every night, but I have no substantiation of this hypothesis.



So my question is twofold:



  1. How does this bizarre phenomenon work wherein my body is apparently conducting electricity from objects which somehow control some anomalous buzz in my headphones?

  2. And how can I make this buzzing sound stop without keeping my body in contact with those objects? Obviously, I can't hold the headphone jack and listen to anything at the same time, and this habit of touching the metallic part of my keyboard is not great for typing nor my wrists which already suffer from CTS.

Any insight is appreciated.










share|improve this question







New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.















  • 7




    How is the mains earth situation in your home? Any of these appliances connected to it?
    – Jeroen3
    Nov 21 at 8:32







  • 18




    +1 for "loud electronic music" as a "solution"
    – Jasen
    Nov 21 at 10:14






  • 2




    I think this question would be improved by editing it for brevity. The story of how you discovered the symptoms of the problem just adds lots of extra reading. All that's needed is "My problem is X. It gets better if I do Y and worse if I do Z. What causes this and how can I fix it?"
    – David Richerby
    Nov 21 at 16:03






  • 2




    The inconvenience of having to continuously touch the metallic part of your keyboard could be mitigated by using an antistatic wristband and attaching the wristband's roach clip to your keyboard. EDIT: Damn, already suggested.
    – Sean
    Nov 21 at 18:16







  • 1




    Dupe : Bose QC20 in-ear headphones 50Hz buzzing noise on PC
    – J...
    Nov 22 at 13:00














up vote
25
down vote

favorite
5












So I have a pair of Bose noise-cancellation headphones that I plug into my keyboard every night to charge them (via my keyboard's USB port). My keyboard happens to be a metallic Apple keyboard. You will see why this may be important to note later.



Over time, I noticed a certain dull, electrical buzzing sound in my right earbud which occurred when I turned the noise-cancellation on. This buzzing sound was not constantly there. It would randomly appear for arbitrary periods of time and then vanish. It wasn't loud either, but it was loud enough to be noticeable and annoying.



For the longest time, I had no clue why this would happen. Sometimes the earbud would be perfectly silent (as it's supposed to be)... and then a buzzing noise would come out of nowhere. This was incredibly annoying and my only remedy was to listen to loud electronic music which blended in with the buzz and made it relatively unnoticeable. Of course, listening to almost any other kind of music proved annoying since my earbud would randomly, intermittently buzz at me.



Finally, one day, I noticed that when I touched my Android phone, the buzzing sound would increase in volume. I thought at first that this was due to my bodily position somehow stretching the wire, but with further testing I confirmed that my Android phone was the culprit. I slowly discovered that touching different objects, even when the headphones were not plugged into the speakers, would result in volume changes of this buzz.



One thing I noticed was that touching the headphone jack, whilst touching the Android phone that increased volume, would silence the buzz. With further testing, I noticed that touching my metallic keyboard would also silence the buzz, even whilst touching the Android phone or under any other circumstance in which there was a buzz.



I finally realized that my body is somehow conducting electricity when touching objects such as my Apple keyboard, headphone jack, or Android phone and that these are all related to the annoying buzz and nullification thereof. I found this bizarre and fascinating.



Ever since this discovery, I've found that I can silence this annoying buzz by pressing any of my fingertips on my metallic keyboard. This is also annoying, since it can make typing awkward to continually have one finger pressing against the metallic part. Nonetheless, I have no idea why this works at all; I suspect it might have something to do with my usage of the keyboard to charge the headphones via its USB port every night, but I have no substantiation of this hypothesis.



So my question is twofold:



  1. How does this bizarre phenomenon work wherein my body is apparently conducting electricity from objects which somehow control some anomalous buzz in my headphones?

  2. And how can I make this buzzing sound stop without keeping my body in contact with those objects? Obviously, I can't hold the headphone jack and listen to anything at the same time, and this habit of touching the metallic part of my keyboard is not great for typing nor my wrists which already suffer from CTS.

Any insight is appreciated.










share|improve this question







New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.















  • 7




    How is the mains earth situation in your home? Any of these appliances connected to it?
    – Jeroen3
    Nov 21 at 8:32







  • 18




    +1 for "loud electronic music" as a "solution"
    – Jasen
    Nov 21 at 10:14






  • 2




    I think this question would be improved by editing it for brevity. The story of how you discovered the symptoms of the problem just adds lots of extra reading. All that's needed is "My problem is X. It gets better if I do Y and worse if I do Z. What causes this and how can I fix it?"
    – David Richerby
    Nov 21 at 16:03






  • 2




    The inconvenience of having to continuously touch the metallic part of your keyboard could be mitigated by using an antistatic wristband and attaching the wristband's roach clip to your keyboard. EDIT: Damn, already suggested.
    – Sean
    Nov 21 at 18:16







  • 1




    Dupe : Bose QC20 in-ear headphones 50Hz buzzing noise on PC
    – J...
    Nov 22 at 13:00












up vote
25
down vote

favorite
5









up vote
25
down vote

favorite
5






5





So I have a pair of Bose noise-cancellation headphones that I plug into my keyboard every night to charge them (via my keyboard's USB port). My keyboard happens to be a metallic Apple keyboard. You will see why this may be important to note later.



Over time, I noticed a certain dull, electrical buzzing sound in my right earbud which occurred when I turned the noise-cancellation on. This buzzing sound was not constantly there. It would randomly appear for arbitrary periods of time and then vanish. It wasn't loud either, but it was loud enough to be noticeable and annoying.



For the longest time, I had no clue why this would happen. Sometimes the earbud would be perfectly silent (as it's supposed to be)... and then a buzzing noise would come out of nowhere. This was incredibly annoying and my only remedy was to listen to loud electronic music which blended in with the buzz and made it relatively unnoticeable. Of course, listening to almost any other kind of music proved annoying since my earbud would randomly, intermittently buzz at me.



Finally, one day, I noticed that when I touched my Android phone, the buzzing sound would increase in volume. I thought at first that this was due to my bodily position somehow stretching the wire, but with further testing I confirmed that my Android phone was the culprit. I slowly discovered that touching different objects, even when the headphones were not plugged into the speakers, would result in volume changes of this buzz.



One thing I noticed was that touching the headphone jack, whilst touching the Android phone that increased volume, would silence the buzz. With further testing, I noticed that touching my metallic keyboard would also silence the buzz, even whilst touching the Android phone or under any other circumstance in which there was a buzz.



I finally realized that my body is somehow conducting electricity when touching objects such as my Apple keyboard, headphone jack, or Android phone and that these are all related to the annoying buzz and nullification thereof. I found this bizarre and fascinating.



Ever since this discovery, I've found that I can silence this annoying buzz by pressing any of my fingertips on my metallic keyboard. This is also annoying, since it can make typing awkward to continually have one finger pressing against the metallic part. Nonetheless, I have no idea why this works at all; I suspect it might have something to do with my usage of the keyboard to charge the headphones via its USB port every night, but I have no substantiation of this hypothesis.



So my question is twofold:



  1. How does this bizarre phenomenon work wherein my body is apparently conducting electricity from objects which somehow control some anomalous buzz in my headphones?

  2. And how can I make this buzzing sound stop without keeping my body in contact with those objects? Obviously, I can't hold the headphone jack and listen to anything at the same time, and this habit of touching the metallic part of my keyboard is not great for typing nor my wrists which already suffer from CTS.

Any insight is appreciated.










share|improve this question







New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











So I have a pair of Bose noise-cancellation headphones that I plug into my keyboard every night to charge them (via my keyboard's USB port). My keyboard happens to be a metallic Apple keyboard. You will see why this may be important to note later.



Over time, I noticed a certain dull, electrical buzzing sound in my right earbud which occurred when I turned the noise-cancellation on. This buzzing sound was not constantly there. It would randomly appear for arbitrary periods of time and then vanish. It wasn't loud either, but it was loud enough to be noticeable and annoying.



For the longest time, I had no clue why this would happen. Sometimes the earbud would be perfectly silent (as it's supposed to be)... and then a buzzing noise would come out of nowhere. This was incredibly annoying and my only remedy was to listen to loud electronic music which blended in with the buzz and made it relatively unnoticeable. Of course, listening to almost any other kind of music proved annoying since my earbud would randomly, intermittently buzz at me.



Finally, one day, I noticed that when I touched my Android phone, the buzzing sound would increase in volume. I thought at first that this was due to my bodily position somehow stretching the wire, but with further testing I confirmed that my Android phone was the culprit. I slowly discovered that touching different objects, even when the headphones were not plugged into the speakers, would result in volume changes of this buzz.



One thing I noticed was that touching the headphone jack, whilst touching the Android phone that increased volume, would silence the buzz. With further testing, I noticed that touching my metallic keyboard would also silence the buzz, even whilst touching the Android phone or under any other circumstance in which there was a buzz.



I finally realized that my body is somehow conducting electricity when touching objects such as my Apple keyboard, headphone jack, or Android phone and that these are all related to the annoying buzz and nullification thereof. I found this bizarre and fascinating.



Ever since this discovery, I've found that I can silence this annoying buzz by pressing any of my fingertips on my metallic keyboard. This is also annoying, since it can make typing awkward to continually have one finger pressing against the metallic part. Nonetheless, I have no idea why this works at all; I suspect it might have something to do with my usage of the keyboard to charge the headphones via its USB port every night, but I have no substantiation of this hypothesis.



So my question is twofold:



  1. How does this bizarre phenomenon work wherein my body is apparently conducting electricity from objects which somehow control some anomalous buzz in my headphones?

  2. And how can I make this buzzing sound stop without keeping my body in contact with those objects? Obviously, I can't hold the headphone jack and listen to anything at the same time, and this habit of touching the metallic part of my keyboard is not great for typing nor my wrists which already suffer from CTS.

Any insight is appreciated.







sound headphones conductivity conductors human-signal






share|improve this question







New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question







New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question






New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked Nov 21 at 8:22









GDP2

23235




23235




New contributor




GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






GDP2 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.







  • 7




    How is the mains earth situation in your home? Any of these appliances connected to it?
    – Jeroen3
    Nov 21 at 8:32







  • 18




    +1 for "loud electronic music" as a "solution"
    – Jasen
    Nov 21 at 10:14






  • 2




    I think this question would be improved by editing it for brevity. The story of how you discovered the symptoms of the problem just adds lots of extra reading. All that's needed is "My problem is X. It gets better if I do Y and worse if I do Z. What causes this and how can I fix it?"
    – David Richerby
    Nov 21 at 16:03






  • 2




    The inconvenience of having to continuously touch the metallic part of your keyboard could be mitigated by using an antistatic wristband and attaching the wristband's roach clip to your keyboard. EDIT: Damn, already suggested.
    – Sean
    Nov 21 at 18:16







  • 1




    Dupe : Bose QC20 in-ear headphones 50Hz buzzing noise on PC
    – J...
    Nov 22 at 13:00












  • 7




    How is the mains earth situation in your home? Any of these appliances connected to it?
    – Jeroen3
    Nov 21 at 8:32







  • 18




    +1 for "loud electronic music" as a "solution"
    – Jasen
    Nov 21 at 10:14






  • 2




    I think this question would be improved by editing it for brevity. The story of how you discovered the symptoms of the problem just adds lots of extra reading. All that's needed is "My problem is X. It gets better if I do Y and worse if I do Z. What causes this and how can I fix it?"
    – David Richerby
    Nov 21 at 16:03






  • 2




    The inconvenience of having to continuously touch the metallic part of your keyboard could be mitigated by using an antistatic wristband and attaching the wristband's roach clip to your keyboard. EDIT: Damn, already suggested.
    – Sean
    Nov 21 at 18:16







  • 1




    Dupe : Bose QC20 in-ear headphones 50Hz buzzing noise on PC
    – J...
    Nov 22 at 13:00







7




7




How is the mains earth situation in your home? Any of these appliances connected to it?
– Jeroen3
Nov 21 at 8:32





How is the mains earth situation in your home? Any of these appliances connected to it?
– Jeroen3
Nov 21 at 8:32





18




18




+1 for "loud electronic music" as a "solution"
– Jasen
Nov 21 at 10:14




+1 for "loud electronic music" as a "solution"
– Jasen
Nov 21 at 10:14




2




2




I think this question would be improved by editing it for brevity. The story of how you discovered the symptoms of the problem just adds lots of extra reading. All that's needed is "My problem is X. It gets better if I do Y and worse if I do Z. What causes this and how can I fix it?"
– David Richerby
Nov 21 at 16:03




I think this question would be improved by editing it for brevity. The story of how you discovered the symptoms of the problem just adds lots of extra reading. All that's needed is "My problem is X. It gets better if I do Y and worse if I do Z. What causes this and how can I fix it?"
– David Richerby
Nov 21 at 16:03




2




2




The inconvenience of having to continuously touch the metallic part of your keyboard could be mitigated by using an antistatic wristband and attaching the wristband's roach clip to your keyboard. EDIT: Damn, already suggested.
– Sean
Nov 21 at 18:16





The inconvenience of having to continuously touch the metallic part of your keyboard could be mitigated by using an antistatic wristband and attaching the wristband's roach clip to your keyboard. EDIT: Damn, already suggested.
– Sean
Nov 21 at 18:16





1




1




Dupe : Bose QC20 in-ear headphones 50Hz buzzing noise on PC
– J...
Nov 22 at 13:00




Dupe : Bose QC20 in-ear headphones 50Hz buzzing noise on PC
– J...
Nov 22 at 13:00










4 Answers
4






active

oldest

votes

















up vote
30
down vote













The "buzz" is almost certainly RF pickup. This can be the mains (low frequency, 50/60/100/120Hz, unlikely in this scenario given a phone is involved) or rectification of the carrier frequency of the phone - remember how old tape players would make a "duh duh, duh duh" sound whenever a text message is received.



Human bodies are conductive. When your skin is dry you are about 100kOhm to 1MOhm. When your skin is wet, that goes down to about 10kOhm to 100kOhm. So there is nothing unusual about becoming a conductor.




As to why touching a metal keyboard kills the hum, or even touching the headphones jack. Basically as you are a nice large conductive area. When connected either to earth (e.g. via the keyboard shell and PC) or to the ground of the phone (e.g. headphones jack), you are basically changing how your body is interacting with the electric fields around you.



EMI is a dark art - it's hard to say exactly what current path you are interrupting, or how you are interacting with the fields. But generally if you ground yourself it stops you acting as an antenna - sort of like shorting yourself out.




One simple option you could try is to buy an anti-static wristband. That would allow yourself to be connected to earth (or to your keyboard) without having to touch the keyboard. Alternatively you could try simply charging your phone from something other than your keyboard to see if that stops noise injection.






share|improve this answer


















  • 1




    ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
    – Wossname
    Nov 21 at 15:22






  • 5




    @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
    – Wayne Conrad
    Nov 21 at 19:47







  • 1




    @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
    – Sean
    Nov 21 at 22:37







  • 3




    @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
    – Wayne Conrad
    Nov 21 at 22:56






  • 2




    @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
    – Jamie Hanrahan
    Nov 22 at 3:03


















up vote
12
down vote













The main fact, in my opinion, is that noise is heard only in right channel.



First thing comes to mind is issue with grounding. But then both channels would receive the noise.



Second - the source of this noise. You must try another headphones to see if noise is caused by headphones or is emitted by the source device.



Third, reposition your phone to the left (if it is on the right) to see if the noise moves into left bud.



Generally I think you will come to the conclusion that something is wrong with right channel of the headphones and headphones are faulty (as the right wire "picks up the RF" as Tom said in his answer, and then amplifies this signal when you turn noise cancellation on, but left does not).






share|improve this answer





























    up vote
    8
    down vote













    My guess is that there is a break in the insulation of the right earbud and that electrical hum from your body is flowing into the noise cancellation amplifier.



    Try wrapping the bud in cling film and see if that stops the buzz.






    share|improve this answer


















    • 3




      I have no idea whatsoever if this answer is right, but it is fascinating.
      – Beska
      Nov 21 at 18:56






    • 6




      @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
      – ale10ander
      Nov 21 at 21:57






    • 1




      I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
      – Wayne Werner
      Nov 22 at 3:10






    • 1




      @ale10ander Dude, whatever floats your boat :)
      – Jasen
      Nov 22 at 6:40

















    up vote
    5
    down vote













    If you have a multimeter available, you can put it into AC voltage measurement mode and try to measure between the different metallic objects. Note that you should only touch the objects with the probe, not with your skin when measuring. For example, touch one probe to the keyboard and other probe to some metal part on the phone.



    If you find a ~60 volt (for 120VAC countries) or ~120 volt (for 240VAC countries) voltage between the objects, it is most likely due to ground potential in the devices. Many mains-powered devices nowadays are designed without a ground wire, and RF filtering capacitors inside the device will leak a small amount of electricity. This becomes apparent when you are between a grounded and an ungrounded object.



    These issues can usually be solved by placing a galvanic isolator between the headphones and the computer. You can search for "3.5mm audio isolator" to find suitable devices.






    share|improve this answer




















      Your Answer





      StackExchange.ifUsing("editor", function ()
      return StackExchange.using("mathjaxEditing", function ()
      StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
      StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
      );
      );
      , "mathjax-editing");

      StackExchange.ifUsing("editor", function ()
      return StackExchange.using("schematics", function ()
      StackExchange.schematics.init();
      );
      , "cicuitlab");

      StackExchange.ready(function()
      var channelOptions =
      tags: "".split(" "),
      id: "135"
      ;
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function()
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled)
      StackExchange.using("snippets", function()
      createEditor();
      );

      else
      createEditor();

      );

      function createEditor()
      StackExchange.prepareEditor(
      heartbeatType: 'answer',
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader:
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      ,
      onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      );



      );






      GDP2 is a new contributor. Be nice, and check out our Code of Conduct.









       

      draft saved


      draft discarded


















      StackExchange.ready(
      function ()
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f407998%2five-become-an-electrical-conductor-for-my-headphones-but-how%23new-answer', 'question_page');

      );

      Post as a guest















      Required, but never shown

























      4 Answers
      4






      active

      oldest

      votes








      4 Answers
      4






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes








      up vote
      30
      down vote













      The "buzz" is almost certainly RF pickup. This can be the mains (low frequency, 50/60/100/120Hz, unlikely in this scenario given a phone is involved) or rectification of the carrier frequency of the phone - remember how old tape players would make a "duh duh, duh duh" sound whenever a text message is received.



      Human bodies are conductive. When your skin is dry you are about 100kOhm to 1MOhm. When your skin is wet, that goes down to about 10kOhm to 100kOhm. So there is nothing unusual about becoming a conductor.




      As to why touching a metal keyboard kills the hum, or even touching the headphones jack. Basically as you are a nice large conductive area. When connected either to earth (e.g. via the keyboard shell and PC) or to the ground of the phone (e.g. headphones jack), you are basically changing how your body is interacting with the electric fields around you.



      EMI is a dark art - it's hard to say exactly what current path you are interrupting, or how you are interacting with the fields. But generally if you ground yourself it stops you acting as an antenna - sort of like shorting yourself out.




      One simple option you could try is to buy an anti-static wristband. That would allow yourself to be connected to earth (or to your keyboard) without having to touch the keyboard. Alternatively you could try simply charging your phone from something other than your keyboard to see if that stops noise injection.






      share|improve this answer


















      • 1




        ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
        – Wossname
        Nov 21 at 15:22






      • 5




        @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
        – Wayne Conrad
        Nov 21 at 19:47







      • 1




        @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
        – Sean
        Nov 21 at 22:37







      • 3




        @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
        – Wayne Conrad
        Nov 21 at 22:56






      • 2




        @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
        – Jamie Hanrahan
        Nov 22 at 3:03















      up vote
      30
      down vote













      The "buzz" is almost certainly RF pickup. This can be the mains (low frequency, 50/60/100/120Hz, unlikely in this scenario given a phone is involved) or rectification of the carrier frequency of the phone - remember how old tape players would make a "duh duh, duh duh" sound whenever a text message is received.



      Human bodies are conductive. When your skin is dry you are about 100kOhm to 1MOhm. When your skin is wet, that goes down to about 10kOhm to 100kOhm. So there is nothing unusual about becoming a conductor.




      As to why touching a metal keyboard kills the hum, or even touching the headphones jack. Basically as you are a nice large conductive area. When connected either to earth (e.g. via the keyboard shell and PC) or to the ground of the phone (e.g. headphones jack), you are basically changing how your body is interacting with the electric fields around you.



      EMI is a dark art - it's hard to say exactly what current path you are interrupting, or how you are interacting with the fields. But generally if you ground yourself it stops you acting as an antenna - sort of like shorting yourself out.




      One simple option you could try is to buy an anti-static wristband. That would allow yourself to be connected to earth (or to your keyboard) without having to touch the keyboard. Alternatively you could try simply charging your phone from something other than your keyboard to see if that stops noise injection.






      share|improve this answer


















      • 1




        ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
        – Wossname
        Nov 21 at 15:22






      • 5




        @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
        – Wayne Conrad
        Nov 21 at 19:47







      • 1




        @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
        – Sean
        Nov 21 at 22:37







      • 3




        @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
        – Wayne Conrad
        Nov 21 at 22:56






      • 2




        @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
        – Jamie Hanrahan
        Nov 22 at 3:03













      up vote
      30
      down vote










      up vote
      30
      down vote









      The "buzz" is almost certainly RF pickup. This can be the mains (low frequency, 50/60/100/120Hz, unlikely in this scenario given a phone is involved) or rectification of the carrier frequency of the phone - remember how old tape players would make a "duh duh, duh duh" sound whenever a text message is received.



      Human bodies are conductive. When your skin is dry you are about 100kOhm to 1MOhm. When your skin is wet, that goes down to about 10kOhm to 100kOhm. So there is nothing unusual about becoming a conductor.




      As to why touching a metal keyboard kills the hum, or even touching the headphones jack. Basically as you are a nice large conductive area. When connected either to earth (e.g. via the keyboard shell and PC) or to the ground of the phone (e.g. headphones jack), you are basically changing how your body is interacting with the electric fields around you.



      EMI is a dark art - it's hard to say exactly what current path you are interrupting, or how you are interacting with the fields. But generally if you ground yourself it stops you acting as an antenna - sort of like shorting yourself out.




      One simple option you could try is to buy an anti-static wristband. That would allow yourself to be connected to earth (or to your keyboard) without having to touch the keyboard. Alternatively you could try simply charging your phone from something other than your keyboard to see if that stops noise injection.






      share|improve this answer














      The "buzz" is almost certainly RF pickup. This can be the mains (low frequency, 50/60/100/120Hz, unlikely in this scenario given a phone is involved) or rectification of the carrier frequency of the phone - remember how old tape players would make a "duh duh, duh duh" sound whenever a text message is received.



      Human bodies are conductive. When your skin is dry you are about 100kOhm to 1MOhm. When your skin is wet, that goes down to about 10kOhm to 100kOhm. So there is nothing unusual about becoming a conductor.




      As to why touching a metal keyboard kills the hum, or even touching the headphones jack. Basically as you are a nice large conductive area. When connected either to earth (e.g. via the keyboard shell and PC) or to the ground of the phone (e.g. headphones jack), you are basically changing how your body is interacting with the electric fields around you.



      EMI is a dark art - it's hard to say exactly what current path you are interrupting, or how you are interacting with the fields. But generally if you ground yourself it stops you acting as an antenna - sort of like shorting yourself out.




      One simple option you could try is to buy an anti-static wristband. That would allow yourself to be connected to earth (or to your keyboard) without having to touch the keyboard. Alternatively you could try simply charging your phone from something other than your keyboard to see if that stops noise injection.







      share|improve this answer














      share|improve this answer



      share|improve this answer








      edited Nov 21 at 23:36

























      answered Nov 21 at 8:36









      Tom Carpenter

      38k269117




      38k269117







      • 1




        ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
        – Wossname
        Nov 21 at 15:22






      • 5




        @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
        – Wayne Conrad
        Nov 21 at 19:47







      • 1




        @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
        – Sean
        Nov 21 at 22:37







      • 3




        @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
        – Wayne Conrad
        Nov 21 at 22:56






      • 2




        @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
        – Jamie Hanrahan
        Nov 22 at 3:03













      • 1




        ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
        – Wossname
        Nov 21 at 15:22






      • 5




        @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
        – Wayne Conrad
        Nov 21 at 19:47







      • 1




        @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
        – Sean
        Nov 21 at 22:37







      • 3




        @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
        – Wayne Conrad
        Nov 21 at 22:56






      • 2




        @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
        – Jamie Hanrahan
        Nov 22 at 3:03








      1




      1




      ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
      – Wossname
      Nov 21 at 15:22




      ESD wristbands have 1 Megohm resistor between the user and ground. Such a weak pulldown probably won't improve EMI issues very much.
      – Wossname
      Nov 21 at 15:22




      5




      5




      @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
      – Wayne Conrad
      Nov 21 at 19:47





      @Sean I think there is a potential safety issue with connecting yourself directly to ground. I think the resistor is important for safety.
      – Wayne Conrad
      Nov 21 at 19:47





      1




      1




      @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
      – Sean
      Nov 21 at 22:37





      @WayneConrad: Even in the kinds of situations ESD wristbands are intended for (i.e., not taking apart power supplies or the like), there isn't anywhere near enough charge separation to hurt you even if it suddenly discharges all at once; the resistor is to keep it from hurting the computer you're working on. Electronic components are a LOT more sensitive to ESD than people are. And in the present situation, given that he isn't getting shocked when he touches his (presumably grounded) keyboard directly, he shouldn't be in any danger from bypassing the resistor.
      – Sean
      Nov 21 at 22:37





      3




      3




      @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
      – Wayne Conrad
      Nov 21 at 22:56




      @Sean My understanding is that the resistor is there in case you came into contact with line current somehow. Which is more likely when you're working on electronics than when working on a computer, so my point is somewhat moot.
      – Wayne Conrad
      Nov 21 at 22:56




      2




      2




      @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
      – Jamie Hanrahan
      Nov 22 at 3:03





      @Sean You are over-generalizing. There are occasions where you have to work on "live" devices. Yes, even AC line-powered ones. Troubleshooting a not-powered device can be next to impossible. So can many types of adjustments. Correct bench practice is to power the device under test from either an isolation transformer or a GFCI / RCD.
      – Jamie Hanrahan
      Nov 22 at 3:03













      up vote
      12
      down vote













      The main fact, in my opinion, is that noise is heard only in right channel.



      First thing comes to mind is issue with grounding. But then both channels would receive the noise.



      Second - the source of this noise. You must try another headphones to see if noise is caused by headphones or is emitted by the source device.



      Third, reposition your phone to the left (if it is on the right) to see if the noise moves into left bud.



      Generally I think you will come to the conclusion that something is wrong with right channel of the headphones and headphones are faulty (as the right wire "picks up the RF" as Tom said in his answer, and then amplifies this signal when you turn noise cancellation on, but left does not).






      share|improve this answer


























        up vote
        12
        down vote













        The main fact, in my opinion, is that noise is heard only in right channel.



        First thing comes to mind is issue with grounding. But then both channels would receive the noise.



        Second - the source of this noise. You must try another headphones to see if noise is caused by headphones or is emitted by the source device.



        Third, reposition your phone to the left (if it is on the right) to see if the noise moves into left bud.



        Generally I think you will come to the conclusion that something is wrong with right channel of the headphones and headphones are faulty (as the right wire "picks up the RF" as Tom said in his answer, and then amplifies this signal when you turn noise cancellation on, but left does not).






        share|improve this answer
























          up vote
          12
          down vote










          up vote
          12
          down vote









          The main fact, in my opinion, is that noise is heard only in right channel.



          First thing comes to mind is issue with grounding. But then both channels would receive the noise.



          Second - the source of this noise. You must try another headphones to see if noise is caused by headphones or is emitted by the source device.



          Third, reposition your phone to the left (if it is on the right) to see if the noise moves into left bud.



          Generally I think you will come to the conclusion that something is wrong with right channel of the headphones and headphones are faulty (as the right wire "picks up the RF" as Tom said in his answer, and then amplifies this signal when you turn noise cancellation on, but left does not).






          share|improve this answer














          The main fact, in my opinion, is that noise is heard only in right channel.



          First thing comes to mind is issue with grounding. But then both channels would receive the noise.



          Second - the source of this noise. You must try another headphones to see if noise is caused by headphones or is emitted by the source device.



          Third, reposition your phone to the left (if it is on the right) to see if the noise moves into left bud.



          Generally I think you will come to the conclusion that something is wrong with right channel of the headphones and headphones are faulty (as the right wire "picks up the RF" as Tom said in his answer, and then amplifies this signal when you turn noise cancellation on, but left does not).







          share|improve this answer














          share|improve this answer



          share|improve this answer








          edited Nov 21 at 8:44

























          answered Nov 21 at 8:39









          Anonymous

          4,9851729




          4,9851729




















              up vote
              8
              down vote













              My guess is that there is a break in the insulation of the right earbud and that electrical hum from your body is flowing into the noise cancellation amplifier.



              Try wrapping the bud in cling film and see if that stops the buzz.






              share|improve this answer


















              • 3




                I have no idea whatsoever if this answer is right, but it is fascinating.
                – Beska
                Nov 21 at 18:56






              • 6




                @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
                – ale10ander
                Nov 21 at 21:57






              • 1




                I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
                – Wayne Werner
                Nov 22 at 3:10






              • 1




                @ale10ander Dude, whatever floats your boat :)
                – Jasen
                Nov 22 at 6:40














              up vote
              8
              down vote













              My guess is that there is a break in the insulation of the right earbud and that electrical hum from your body is flowing into the noise cancellation amplifier.



              Try wrapping the bud in cling film and see if that stops the buzz.






              share|improve this answer


















              • 3




                I have no idea whatsoever if this answer is right, but it is fascinating.
                – Beska
                Nov 21 at 18:56






              • 6




                @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
                – ale10ander
                Nov 21 at 21:57






              • 1




                I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
                – Wayne Werner
                Nov 22 at 3:10






              • 1




                @ale10ander Dude, whatever floats your boat :)
                – Jasen
                Nov 22 at 6:40












              up vote
              8
              down vote










              up vote
              8
              down vote









              My guess is that there is a break in the insulation of the right earbud and that electrical hum from your body is flowing into the noise cancellation amplifier.



              Try wrapping the bud in cling film and see if that stops the buzz.






              share|improve this answer














              My guess is that there is a break in the insulation of the right earbud and that electrical hum from your body is flowing into the noise cancellation amplifier.



              Try wrapping the bud in cling film and see if that stops the buzz.







              share|improve this answer














              share|improve this answer



              share|improve this answer








              edited Nov 22 at 6:40

























              answered Nov 21 at 10:19









              Jasen

              9,4601428




              9,4601428







              • 3




                I have no idea whatsoever if this answer is right, but it is fascinating.
                – Beska
                Nov 21 at 18:56






              • 6




                @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
                – ale10ander
                Nov 21 at 21:57






              • 1




                I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
                – Wayne Werner
                Nov 22 at 3:10






              • 1




                @ale10ander Dude, whatever floats your boat :)
                – Jasen
                Nov 22 at 6:40












              • 3




                I have no idea whatsoever if this answer is right, but it is fascinating.
                – Beska
                Nov 21 at 18:56






              • 6




                @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
                – ale10ander
                Nov 21 at 21:57






              • 1




                I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
                – Wayne Werner
                Nov 22 at 3:10






              • 1




                @ale10ander Dude, whatever floats your boat :)
                – Jasen
                Nov 22 at 6:40







              3




              3




              I have no idea whatsoever if this answer is right, but it is fascinating.
              – Beska
              Nov 21 at 18:56




              I have no idea whatsoever if this answer is right, but it is fascinating.
              – Beska
              Nov 21 at 18:56




              6




              6




              @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
              – ale10ander
              Nov 21 at 21:57




              @Jasen Can you clarify what you are suggesting be wrapped in cling wrap? As the question stands it's ambiguous if you mean the earbud or the body.
              – ale10ander
              Nov 21 at 21:57




              1




              1




              I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
              – Wayne Werner
              Nov 22 at 3:10




              I have a pair of Cowin E7 noise cancellation headphones that will do some weird sounds with specific contact positions with the headphones. I wonder if that's due to this.
              – Wayne Werner
              Nov 22 at 3:10




              1




              1




              @ale10ander Dude, whatever floats your boat :)
              – Jasen
              Nov 22 at 6:40




              @ale10ander Dude, whatever floats your boat :)
              – Jasen
              Nov 22 at 6:40










              up vote
              5
              down vote













              If you have a multimeter available, you can put it into AC voltage measurement mode and try to measure between the different metallic objects. Note that you should only touch the objects with the probe, not with your skin when measuring. For example, touch one probe to the keyboard and other probe to some metal part on the phone.



              If you find a ~60 volt (for 120VAC countries) or ~120 volt (for 240VAC countries) voltage between the objects, it is most likely due to ground potential in the devices. Many mains-powered devices nowadays are designed without a ground wire, and RF filtering capacitors inside the device will leak a small amount of electricity. This becomes apparent when you are between a grounded and an ungrounded object.



              These issues can usually be solved by placing a galvanic isolator between the headphones and the computer. You can search for "3.5mm audio isolator" to find suitable devices.






              share|improve this answer
























                up vote
                5
                down vote













                If you have a multimeter available, you can put it into AC voltage measurement mode and try to measure between the different metallic objects. Note that you should only touch the objects with the probe, not with your skin when measuring. For example, touch one probe to the keyboard and other probe to some metal part on the phone.



                If you find a ~60 volt (for 120VAC countries) or ~120 volt (for 240VAC countries) voltage between the objects, it is most likely due to ground potential in the devices. Many mains-powered devices nowadays are designed without a ground wire, and RF filtering capacitors inside the device will leak a small amount of electricity. This becomes apparent when you are between a grounded and an ungrounded object.



                These issues can usually be solved by placing a galvanic isolator between the headphones and the computer. You can search for "3.5mm audio isolator" to find suitable devices.






                share|improve this answer






















                  up vote
                  5
                  down vote










                  up vote
                  5
                  down vote









                  If you have a multimeter available, you can put it into AC voltage measurement mode and try to measure between the different metallic objects. Note that you should only touch the objects with the probe, not with your skin when measuring. For example, touch one probe to the keyboard and other probe to some metal part on the phone.



                  If you find a ~60 volt (for 120VAC countries) or ~120 volt (for 240VAC countries) voltage between the objects, it is most likely due to ground potential in the devices. Many mains-powered devices nowadays are designed without a ground wire, and RF filtering capacitors inside the device will leak a small amount of electricity. This becomes apparent when you are between a grounded and an ungrounded object.



                  These issues can usually be solved by placing a galvanic isolator between the headphones and the computer. You can search for "3.5mm audio isolator" to find suitable devices.






                  share|improve this answer












                  If you have a multimeter available, you can put it into AC voltage measurement mode and try to measure between the different metallic objects. Note that you should only touch the objects with the probe, not with your skin when measuring. For example, touch one probe to the keyboard and other probe to some metal part on the phone.



                  If you find a ~60 volt (for 120VAC countries) or ~120 volt (for 240VAC countries) voltage between the objects, it is most likely due to ground potential in the devices. Many mains-powered devices nowadays are designed without a ground wire, and RF filtering capacitors inside the device will leak a small amount of electricity. This becomes apparent when you are between a grounded and an ungrounded object.



                  These issues can usually be solved by placing a galvanic isolator between the headphones and the computer. You can search for "3.5mm audio isolator" to find suitable devices.







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered Nov 22 at 6:38









                  jpa

                  1,461711




                  1,461711




















                      GDP2 is a new contributor. Be nice, and check out our Code of Conduct.









                       

                      draft saved


                      draft discarded


















                      GDP2 is a new contributor. Be nice, and check out our Code of Conduct.












                      GDP2 is a new contributor. Be nice, and check out our Code of Conduct.











                      GDP2 is a new contributor. Be nice, and check out our Code of Conduct.













                       


                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function ()
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f407998%2five-become-an-electrical-conductor-for-my-headphones-but-how%23new-answer', 'question_page');

                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown






                      Popular posts from this blog

                      How to check contact read email or not when send email to Individual?

                      Displaying single band from multi-band raster using QGIS

                      How many registers does an x86_64 CPU actually have?