Square vs Round pad
Clash Royale CLAN TAG#URR8PPP
$begingroup$
I'm curious why PCBs have one square pad in row for 0.1" headers.
What is purpose of putting one square pad? What it indicates? Can you push more amps through square pad than round?
header pads
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
$endgroup$
add a comment |
$begingroup$
I'm curious why PCBs have one square pad in row for 0.1" headers.
What is purpose of putting one square pad? What it indicates? Can you push more amps through square pad than round?
header pads
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
$endgroup$
add a comment |
$begingroup$
I'm curious why PCBs have one square pad in row for 0.1" headers.
What is purpose of putting one square pad? What it indicates? Can you push more amps through square pad than round?
header pads
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
$endgroup$
I'm curious why PCBs have one square pad in row for 0.1" headers.
What is purpose of putting one square pad? What it indicates? Can you push more amps through square pad than round?
header pads
header pads
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
asked Feb 8 at 17:05
SilvioCroSilvioCro
105110
105110
add a comment |
add a comment |
4 Answers
4
active
oldest
votes
$begingroup$
This is to identify which pin is "pin 1".
In the case of a single-row header with no orientation key, this might not really matter, but the layout tool might do this by default and the designer didn't think to turn it off.
If this were to be used with a connector that does have an orientation key, I'd much rather also have a pin 1 indicator in silkscreen, so that the orientation can be checked after the connector is loaded (and without having to flip the board over).
Can you push more amps through square pad than round?
No, it won't cause any significant difference on the circuit performance.
(As pointed out in comments, for an RF or high-voltage application you might need to consider more carefully before using this method of orientation marking)
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
$endgroup$
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
add a comment |
$begingroup$
Not a standard, but it's useful to mark where pin 1 is. This might be useful if you don't have a silkscreen, but you wish to mark the orientation of the socket.
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
$endgroup$
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
1
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
add a comment |
$begingroup$
It is there to mark the location of a specific pin (mostly pin 1). It helps in deciding the orientation in which a component should be placed.
No you can't push more amps through the square pad. Check to see if the trace running to that pad is wider than the other traces, if not than it is similar to the others.
The square pad doesn't make a electronic difference when compared to round pads.
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
$endgroup$
add a comment |
$begingroup$
It indicates the location of pin 1
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
$endgroup$
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
);
);
, "mathjax-editing");
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f421253%2fsquare-vs-round-pad%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
4 Answers
4
active
oldest
votes
4 Answers
4
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
This is to identify which pin is "pin 1".
In the case of a single-row header with no orientation key, this might not really matter, but the layout tool might do this by default and the designer didn't think to turn it off.
If this were to be used with a connector that does have an orientation key, I'd much rather also have a pin 1 indicator in silkscreen, so that the orientation can be checked after the connector is loaded (and without having to flip the board over).
Can you push more amps through square pad than round?
No, it won't cause any significant difference on the circuit performance.
(As pointed out in comments, for an RF or high-voltage application you might need to consider more carefully before using this method of orientation marking)
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
$endgroup$
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
add a comment |
$begingroup$
This is to identify which pin is "pin 1".
In the case of a single-row header with no orientation key, this might not really matter, but the layout tool might do this by default and the designer didn't think to turn it off.
If this were to be used with a connector that does have an orientation key, I'd much rather also have a pin 1 indicator in silkscreen, so that the orientation can be checked after the connector is loaded (and without having to flip the board over).
Can you push more amps through square pad than round?
No, it won't cause any significant difference on the circuit performance.
(As pointed out in comments, for an RF or high-voltage application you might need to consider more carefully before using this method of orientation marking)
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
$endgroup$
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
add a comment |
$begingroup$
This is to identify which pin is "pin 1".
In the case of a single-row header with no orientation key, this might not really matter, but the layout tool might do this by default and the designer didn't think to turn it off.
If this were to be used with a connector that does have an orientation key, I'd much rather also have a pin 1 indicator in silkscreen, so that the orientation can be checked after the connector is loaded (and without having to flip the board over).
Can you push more amps through square pad than round?
No, it won't cause any significant difference on the circuit performance.
(As pointed out in comments, for an RF or high-voltage application you might need to consider more carefully before using this method of orientation marking)
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
$endgroup$
This is to identify which pin is "pin 1".
In the case of a single-row header with no orientation key, this might not really matter, but the layout tool might do this by default and the designer didn't think to turn it off.
If this were to be used with a connector that does have an orientation key, I'd much rather also have a pin 1 indicator in silkscreen, so that the orientation can be checked after the connector is loaded (and without having to flip the board over).
Can you push more amps through square pad than round?
No, it won't cause any significant difference on the circuit performance.
(As pointed out in comments, for an RF or high-voltage application you might need to consider more carefully before using this method of orientation marking)
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
edited Feb 8 at 17:18
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
answered Feb 8 at 17:09
The PhotonThe Photon
85.7k398198
85.7k398198
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
add a comment |
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
$begingroup$
Comments are not for extended discussion; this conversation has been moved to chat.
$endgroup$
– Dave Tweed♦
Feb 8 at 22:07
add a comment |
$begingroup$
Not a standard, but it's useful to mark where pin 1 is. This might be useful if you don't have a silkscreen, but you wish to mark the orientation of the socket.
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
$endgroup$
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
1
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
add a comment |
$begingroup$
Not a standard, but it's useful to mark where pin 1 is. This might be useful if you don't have a silkscreen, but you wish to mark the orientation of the socket.
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
$endgroup$
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
1
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
add a comment |
$begingroup$
Not a standard, but it's useful to mark where pin 1 is. This might be useful if you don't have a silkscreen, but you wish to mark the orientation of the socket.
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
$endgroup$
Not a standard, but it's useful to mark where pin 1 is. This might be useful if you don't have a silkscreen, but you wish to mark the orientation of the socket.
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
answered Feb 8 at 17:07
awjloganawjlogan
3,72411328
3,72411328
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
1
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
add a comment |
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
1
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
$begingroup$
But in case with Arduino Nano(for example), it doesn't help.
$endgroup$
– SilvioCro
Feb 8 at 17:09
1
1
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro Why not? Looking at a picture of the Nano (and some knockoffs), the TX1 pin is usually square, so you could work out the orientation based on that.
$endgroup$
– awjlogan
Feb 8 at 17:14
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
$begingroup$
@SilvioCro, It is a common practice, most PCB software / manufacturer prefer this and since it doesn't change much electronically (except RF), it is fine to just add it
$endgroup$
– Electric_90
Feb 8 at 17:33
add a comment |
$begingroup$
It is there to mark the location of a specific pin (mostly pin 1). It helps in deciding the orientation in which a component should be placed.
No you can't push more amps through the square pad. Check to see if the trace running to that pad is wider than the other traces, if not than it is similar to the others.
The square pad doesn't make a electronic difference when compared to round pads.
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
$endgroup$
add a comment |
$begingroup$
It is there to mark the location of a specific pin (mostly pin 1). It helps in deciding the orientation in which a component should be placed.
No you can't push more amps through the square pad. Check to see if the trace running to that pad is wider than the other traces, if not than it is similar to the others.
The square pad doesn't make a electronic difference when compared to round pads.
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
$endgroup$
add a comment |
$begingroup$
It is there to mark the location of a specific pin (mostly pin 1). It helps in deciding the orientation in which a component should be placed.
No you can't push more amps through the square pad. Check to see if the trace running to that pad is wider than the other traces, if not than it is similar to the others.
The square pad doesn't make a electronic difference when compared to round pads.
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
$endgroup$
It is there to mark the location of a specific pin (mostly pin 1). It helps in deciding the orientation in which a component should be placed.
No you can't push more amps through the square pad. Check to see if the trace running to that pad is wider than the other traces, if not than it is similar to the others.
The square pad doesn't make a electronic difference when compared to round pads.
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
edited Feb 8 at 17:17
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
answered Feb 8 at 17:10
Electric_90Electric_90
1,252419
1,252419
add a comment |
add a comment |
$begingroup$
It indicates the location of pin 1
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
$endgroup$
add a comment |
$begingroup$
It indicates the location of pin 1
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
$endgroup$
add a comment |
$begingroup$
It indicates the location of pin 1
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
$endgroup$
It indicates the location of pin 1
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
answered Feb 8 at 17:07
uglyoldbobuglyoldbob
1286
1286
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f421253%2fsquare-vs-round-pad%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown