In radio, narrowband describes a channel in which the bandwidth of the message does not significantly exceed the channel's coherence bandwidth.
In the study of wired channels, narrowband implies that the channel under consideration is sufficiently narrow that its frequency response can be considered flat. The message bandwidth will therefore be less than the coherence bandwidth of the channel. That is, no channel has perfectly flat fading, but the analysis of many aspects of wireless systems is greatly simplified if flat fading can be assumed.
Narrowband can also be used with the audio spectrum to describe sounds which occupy a narrow range of frequencies.
In telephony, narrowband is usually considered to cover frequencies 300–3400 Hz.
Contents
1Two-way radio narrowband
2See also
3References
4External links
Two-way radio narrowband
Two-Way Radio Narrowbanding refers to a U.S. Federal Communications Commission (FCC) Order issued in December 2004 requiring all CFR 47 Part 90 VHF (150-174 MHz) and UHF (421-470 MHz) PLMR (Private Land Mobile Radio) licensees operating legacy wideband (25 kHz bandwidth) voice or data/SCADA systems to migrate to narrowband (12.5 kHz bandwidth or equivalent) systems by January 1, 2013.[1]
See also
Electromagnetic Interference
Land Mobile Radio Service
Rural Internet
Broadband
Wideband
Ultra-wideband
References
^FCC Order issued in December of 2004
External links
FCC website
FCC Part 90 LMR VHF/UHF Narrowbanding Information and Licensee Resources
Clash Royale CLAN TAG #URR8PPP up vote 1 down vote favorite I'm using WordPress 4.9.8, CiviCRM to 5.5.1, I usually send email to contact by Search> Find contacts View contact details Action> Send email Send email ok, Contact received mail ok like picture But status only Email sent though contact read email or not. So, can CiviCRM can change status to Email read when contact read email? wordpress email share | improve this question asked Sep 26 at 0:12 ToanLuong 49 9 add a comment  | up vote 1 down vote favorite I'm using WordPress 4.9.8, CiviCRM to 5.5.1, I usually send email to contact by Search> Find contacts View contact details Action> Send email Send email ok, Contact received mail ok like picture But status only Email sent though contact read email or not. So, can CiviCRM can change status to Email read when contact read email? wordpress email share | improve this questi...
Clash Royale CLAN TAG #URR8PPP up vote 2 down vote favorite I am currently learning reverse engineering and am studying the flags register. I had in my mind that rflags was just another name for one of the 16 general purpose registers, for example rax or rbx . But it looks like rflags is actually an additional register. So that makes 17 registers in total... how many more could there be? I have spent at least an hour on this and found numerous different answers. The best answer so far is this, which says that there are 40 registers in total. 16 General Purpose Registers 2 Status Registers 6 Code Segment Registers 16 SSE Registers 8 FPU/MMX Registers But if I add that up, I get 48. Could anybody provide an official answer on how many registers an x86_64 CPU has (e.g. an Intel i7). Additionally, I have seen references to 'hardware' and 'architectural' registers. What are those registers and how many are there? register x86-64 share | improve this...
Clash Royale CLAN TAG #URR8PPP 1 How can I extract a single band from multi-band raster in QGIS? I have an remote sensed image which has 6 bands (including NDVI band), I want to display each band separately, but have no idea how to do. I have seen some questions similar here but none worked for me. The original image (has 6 bands) is: I want to display the band 6 which should be like this: But I tried gdal_translate, and couldn't get the correct result. What I have got is: qgis raster multi-band share | improve this question edited Mar 5 at 0:53 Summer asked Mar 4 at 6:42 Summer Summer 23 6 Is this any help gis.stackexchange.com/questions/220658/… ? if not gis.stackexchange.com/questions/62133/… might help. – Michael Stimson Mar 4 at 6:46 Thanks for answering but when I used gdal_translate, qgis showed that 'Error 4: Kayena.tif: No such file or directory". Would you know how to fi...
