mjhjmtu

The bandwidth Δf=f2−f1displaystyle Delta f=f_2-f_1 of a damped oscillator is shown on a graph of energy versus frequency. The Q factor of the damped oscillator, or filter, is fcΔfdisplaystyle frac f_cDelta f. The higher the Q, the narrower and ‘sharper’ the peak is.

In physics and engineering the quality factor or Q factor is a dimensionless parameter that describes how underdamped an oscillator or resonator is,^[1] and characterizes a resonator's bandwidth relative to its centre frequency.^[2]
Higher Q indicates a lower rate of energy loss relative to the stored energy of the resonator; the oscillations die out more slowly. A pendulum suspended from a high-quality bearing, oscillating in air, has a high Q, while a pendulum immersed in oil has a low one. Resonators with high quality factors have low damping, so that they ring or vibrate longer.

Explanation

Q factor is a parameter that describes the resonance behavior of an underdamped harmonic oscillator (resonator). Sinusoidally driven resonators having higher Q factors resonate with greater amplitudes (at the resonant frequency) but have a smaller range of frequencies around that frequency for which they resonate; the range of frequencies for which the oscillator resonates is called the bandwidth. Thus, a high-Q tuned circuit in a radio receiver would be more difficult to tune, but would have more selectivity; it would do a better job of filtering out signals from other stations that lie nearby on the spectrum. High-Q oscillators oscillate with a smaller range of frequencies and are more stable. (See oscillator phase noise.)

The quality factor of oscillators varies substantially from system to system, depending on their construction. Systems for which damping is important (such as dampers keeping a door from slamming shut) have Q near ​¹⁄₂. Clocks, lasers, and other resonating systems that need either strong resonance or high frequency stability have high quality factors. Tuning forks have quality factors around 1000. The quality factor of atomic clocks, superconducting RF cavities used in accelerators, and some high-Q lasers can reach as high as 10^11[3] and higher.^[4]

There are many alternative quantities used by physicists and engineers to describe how damped an oscillator is. Important examples include: the damping ratio, relative bandwidth, linewidth and bandwidth measured in octaves.

The concept of Q originated with K. S. Johnson of Western Electric Company's Engineering Department while evaluating the quality of coils (inductors). His choice of the symbol Q was only because, at the time, all other letters of the alphabet were taken. The term was not intended as an abbreviation for "quality" or "quality factor", although these terms have grown to be associated with it.
^[5][6][7]

Definition

The definition of Q since its first use in 1914 has been generalized to apply to coils and condensers, resonant circuits, resonant devices, resonant transmission lines, cavity resonators, material Q and spectral lines.^[5]

Resonant devices

In the context of resonators, there are two common definitions for Q, which aren't exactly equivalent. They become approximately equivalent as Q becomes larger, meaning the resonator becomes less damped. One of these definitions is the frequency-to-bandwidth ratio of the resonator:^[5]

Q =def frΔf=ωrΔω,displaystyle Q stackrel mathrm def = frac f_rDelta f=frac omega _rDelta omega ,,

where f_r is the resonant frequency, Δf is the resonance width or full width at half maximum (FWHM) i.e. the bandwidth over which the power of vibration is greater than half the power at the resonant frequency, ω_r = 2πf_r is the angular resonant frequency, and Δω is the angular half-power bandwidth.

Coils and condensers

The other common nearly equivalent definition for Q is the ratio of the energy stored in the oscillating resonator to the energy dissipated per cycle by damping processes^[8][9][5]:

Q =def 2π×energy storedenergy dissipated per cycle=2πfr×energy storedpower loss.displaystyle Q stackrel mathrm def = 2pi times frac textenergy storedtextenergy dissipated per cycle=2pi f_rtimes frac textenergy storedtextpower loss.,

The factor 2π makes Q expressible in simpler terms, involving only the coefficients of the second-order differential equation describing most resonant systems, electrical or mechanical. In electrical systems, the stored energy is the sum of energies stored in lossless inductors and capacitors; the lost energy is the sum of the energies dissipated in resistors per cycle. In mechanical systems, the stored energy is the maximum possible stored energy, or the total energy, i.e. the sum of the potential and kinetic energies at some point in time; the lost energy is the work done by an external conservative force, per cycle, to maintain amplitude.

More generally and in the context of reactive component specification (especially inductors), the frequency-dependent definition of Q is used:^{[8][10][not in citation given (See discussion.)][9]}

Q(ω)=ω×maximum energy storedpower loss,displaystyle Q(omega )=omega times frac textmaximum energy storedtextpower loss,,

where ω is the angular frequency at which the stored energy and power loss are measured. This definition is consistent with its usage in describing circuits with a single reactive element (capacitor or inductor), where it can be shown to be equal to the ratio of reactive power to real power. (See Individual reactive components.)

Q factor and damping

The Q factor determines the qualitative behavior of simple damped oscillators. (For mathematical details about these systems and their behavior see harmonic oscillator and linear time invariant (LTI) system.)

• A system with low quality factor (Q < ​¹⁄₂) is said to be overdamped. Such a system doesn't oscillate at all, but when displaced from its equilibrium steady-state output it returns to it by exponential decay, approaching the steady state value asymptotically. It has an impulse response that is the sum of two decaying exponential functions with different rates of decay. As the quality factor decreases the slower decay mode becomes stronger relative to the faster mode and dominates the system's response resulting in a slower system. A second-order low-pass filter with a very low quality factor has a nearly first-order step response; the system's output responds to a step input by slowly rising toward an asymptote.


• A system with high quality factor (Q > ​¹⁄₂) is said to be underdamped. Underdamped systems combine oscillation at a specific frequency with a decay of the amplitude of the signal. Underdamped systems with a low quality factor (a little above Q = ​¹⁄₂) may oscillate only once or a few times before dying out. As the quality factor increases, the relative amount of damping decreases. A high-quality bell rings with a single pure tone for a very long time after being struck. A purely oscillatory system, such as a bell that rings forever, has an infinite quality factor. More generally, the output of a second-order low-pass filter with a very high quality factor responds to a step input by quickly rising above, oscillating around, and eventually converging to a steady-state value.


• A system with an intermediate quality factor (Q = ​¹⁄₂) is said to be critically damped. Like an overdamped system, the output does not oscillate, and does not overshoot its steady-state output (i.e., it approaches a steady-state asymptote). Like an underdamped response, the output of such a system responds quickly to a unit step input. Critical damping results in the fastest response (approach to the final value) possible without overshoot. Real system specifications usually allow some overshoot for a faster initial response or require a slower initial response to provide a safety margin against overshoot.

In negative feedback systems, the dominant closed-loop response is often well-modeled by a second-order system. The phase margin of the open-loop system sets the quality factor Q of the closed-loop system; as the phase margin decreases, the approximate second-order closed-loop system is made more oscillatory (i.e., has a higher quality factor).

Quality factors of common systems

• A unity-gain Sallen–Key lowpass filter topology with equal capacitors and equal resistors is critically damped (i.e., Q = ​¹⁄₂).


• A second-order Butterworth filter (i.e., continuous-time filter with the flattest passband frequency response) has an underdamped Q = ​¹⁄_√2.^[11]


• A Bessel filter (i.e., continuous-time filter with flattest group delay) has an underdamped Q = ​¹⁄_√3.^{[citation needed]}

Physical interpretation

Physically speaking, Q is 2π times the ratio of the total energy stored divided by the energy lost in a single cycle or equivalently the ratio of the stored energy to the energy dissipated over one radian of the oscillation.^[12]

It is a dimensionless parameter that compares the exponential time constant τ for decay of an oscillating physical system's amplitude to its oscillation period. Equivalently, it compares the frequency at which a system oscillates to the rate at which it dissipates its energy.

Equivalently (for large values of Q), the Q factor is approximately the number of oscillations required for a freely oscillating system's energy to fall off to e^−2π, or about ​¹⁄₅₃₅ or 0.2%, of its original energy.^[13] This means the amplitude falls off to approximately e^−π or 4% of its original amplitude.^[14]

The width (bandwidth) of the resonance is given by

Δf=f0Q,displaystyle Delta f=frac f_0Q,,

where f₀ is the resonant frequency, and Δf, the bandwidth, is the width of the range of frequencies for which the energy is at least half its peak value.

The resonant frequency is often expressed in natural units (radians per second), rather than using the f₀ in hertz, as

ω0=2πf0.displaystyle omega _0=2pi f_0.

The factors Q, damping ratio ζ, attenuation rate α, and exponential time constant τ are related such that:^[15]

Q=12ζ=ω02α=τω02,displaystyle Q=frac 12zeta =omega _0 over 2alpha =tau omega _0 over 2,

and the damping ratio can be expressed as:

ζ=12Q=αω0=1τω0.displaystyle zeta =frac 12Q=alpha over omega _0=1 over tau omega _0.

The envelope of oscillation decays proportional to e^−αt or e^−t/τ, where α and τ can be expressed as:

α=ω02Q=ζω0=1τdisplaystyle alpha =omega _0 over 2Q=zeta omega _0=1 over tau

and

τ=2Qω0=1ζω0=1α.displaystyle tau =2Q over omega _0=1 over zeta omega _0=1 over alpha .

The energy of oscillation, or the power dissipation, decays twice as fast, that is, as the square of the amplitude, as e^−2αt or e^−2t|τ.

For a two-pole lowpass filter, the transfer function of the filter is^[15]

H(s)=ω02s2+ω0Q⏟2ζω0=2αs+ω02displaystyle H(s)=frac omega _0^2s^2+underbrace frac omega _0Q _2zeta omega _0=2alpha s+omega _0^2,

For this system, when Q > ​¹⁄₂ (i.e., when the system is underdamped), it has two complex conjugate poles that each have a real part of −α. That is, the attenuation parameter α represents the rate of exponential decay of the oscillations (that is, of the output after an impulse) into the system. A higher quality factor implies a lower attenuation rate, and so high-Q systems oscillate for many cycles. For example, high-quality bells have an approximately pure sinusoidal tone for a long time after being struck by a hammer.

Filter type (2nd order) Transfer function[16] Lowpass H(s)=ω02s2+ω0Qs+ω02displaystyle H(s)=frac omega _0^2s^2+frac omega _0Qs+omega _0^2 Bandpass H(s)=ω0Qss2+ω0Qs+ω02displaystyle H(s)=frac frac omega _0Qss^2+frac omega _0Qs+omega _0^2 Notch (Bandstop) H(s)=s2+ω02s2+ω0Qs+ω02displaystyle H(s)=frac s^2+omega _0^2s^2+frac omega _0Qs+omega _0^2 Highpass H(s)=s2s2+ω0Qs+ω02displaystyle H(s)=frac s^2s^2+frac omega _0Qs+omega _0^2

Electrical systems

A graph of a filter's gain magnitude, illustrating the concept of −3 dB at a voltage gain of 0.707 or half-power bandwidth. The frequency axis of this symbolic diagram can be linear or logarithmically scaled.

For an electrically resonant system, the Q factor represents the effect of electrical resistance and, for electromechanical resonators such as quartz crystals, mechanical friction.

Relationship between Q and bandwidth

The 2-sided bandwidth relative to a resonant frequency of F₀ Hz is F₀/Q.

For example, an antenna tuned to have a Q value of 10 and a centre frequency of 100 kHz would have a 3 dB bandwidth of 10 kHz.

In audio, bandwidth is often expressed in terms of octaves. Then the relationship between Q and bandwidth is

Q = 2BW22BW−1 = 12sinh⁡(ln⁡(2)2BW),displaystyle Q = frac 2^frac BW22^BW-1 = frac 12sinh left(frac ln(2)2BWright),

where BW is the bandwidth in octaves.^[17]

RLC circuits

In an ideal series RLC circuit, and in a tuned radio frequency receiver (TRF) the Q factor is:^[18]

Q=1RLC=ω0LR=1ω0RCdisplaystyle Q=frac 1Rsqrt frac LC=frac omega _0LR=frac 1omega _0RC

where R, L and C are the resistance, inductance and capacitance of the tuned circuit, respectively. The larger the series resistance, the lower the circuit Q.

For a parallel RLC circuit, the Q factor is the inverse of the series case:^[19][18]

Q=RCL=Rω0L=ω0RCdisplaystyle Q=Rsqrt frac CL=frac Romega _0L=omega _0RC^[20]

Consider a circuit where R, L and C are all in parallel. The lower the parallel resistance, the more effect it will have in damping the circuit and thus the lower the Q. This is useful in filter design to determine the bandwidth.

In a parallel LC circuit where the main loss is the resistance of the inductor, R, in series with the inductance, L, Q is as in the series circuit. This is a common circumstance for resonators, where limiting the resistance of the inductor to improve Q and narrow the bandwidth is the desired result.

Individual reactive components

The Q of an individual reactive component depends on the frequency at which it is evaluated, which is typically the resonant frequency of the circuit that it is used in. The Q of an inductor with a series loss resistance is the Q of a resonant circuit using that inductor (including its series loss) and a perfect capacitor.^[21]

QL=XLRL=ω0LRLdisplaystyle Q_L=frac X_LR_L=frac omega _0LR_L

where:

• 
  ω₀ is the resonance frequency in radians per second,


• 
  L is the inductance,


• 
  X_L is the inductive reactance, and


• 
  R_L is the series resistance of the inductor.

The Q of a capacitor with a series loss resistance is the same as the Q of a resonant circuit using that capacitor with a perfect inductor:^[21]

QC=−XCRC=1ω0CRCdisplaystyle Q_C=frac -X_CR_C=frac 1omega _0CR_C

where:

• 
  ω₀ is the resonance frequency in radians per second,


• 
  C is the capacitance,


• 
  X_C is the capacitive reactance, and


• 
  R_C is the series resistance of the capacitor.

In general, the Q of a resonator involving a series combination of a capacitor and an inductor can be determined from the Q values of the components, whether their losses come from series resistance or otherwise:^[21]

Q=11QL+1QCdisplaystyle Q=frac 1frac 1Q_L+frac 1Q_C

Mechanical systems

For a single damped mass-spring system, the Q factor represents the effect of simplified viscous damping or drag, where the damping force or drag force is proportional to velocity. The formula for the Q factor is:

Q=MkD,displaystyle Q=frac sqrt MkD,,

where M is the mass, k is the spring constant, and D is the damping coefficient, defined by the equation F_damping = −Dv, where v is the velocity.^[22]

Acoustical systems

The Q of a musical instrument is critical; an excessively high Q in a resonator will not evenly amplify the multiple frequencies an instrument produces . For this reason, string instruments often have bodies with complex shapes, so that they produce a wide range of frequencies fairly evenly.

The Q of a brass instrument or wind instrument needs to be high enough to pick one frequency out of the broader-spectrum buzzing of the lips or reed.
By contrast, a vuvuzela is made of flexible plastic, and therefore has a very low Q for a brass instrument, giving it a muddy, breathy tone. Instruments made of stiffer plastic, brass, or wood have higher-Q. An excessively high Q can make it harder to hit a note. Q in an instrument may vary across frequencies, but this may not be desirable.

Helmholtz resonators have a very high Q, as they are designed for picking out a very narrow range of frequencies.

Optical systems

In optics, the Q factor of a resonant cavity is given by

Q=2πfoEP,displaystyle Q=frac 2pi f_o,EP,,

where f_o is the resonant frequency, E is the stored energy in the cavity, and P = −dE/dt is the power dissipated. The optical Q is equal to the ratio of the resonant frequency to the bandwidth of the cavity resonance. The average lifetime of a resonant photon in the cavity is proportional to the cavity's Q. If the Q factor of a laser's cavity is abruptly changed from a low value to a high one, the laser will emit a pulse of light that is much more intense than the laser's normal continuous output. This technique is known as Q-switching.

See also

• Acoustic resonance


• Attenuation


• Chu–Harrington limit


• Phase margin


• Q meter


• Q multiplier


• Dissipation factor

References

Further reading

External links

Wikimedia Commons has media related to Quality factor.

• [http://www.sengpielaudio.com/calculator-cutoffFrequencies.htm Calculating the cut-off frequencies when center frequency and Q factor is given


• Explanation of Q factor in radio tuning circuits