Are these integrated diagonal wall braces structurally important?
Clash Royale CLAN TAG#URR8PPP
I was helping a friend expand the width of a closet door, and when we pulled the drywall off the interior wall frame, we noticed some 45-degree wall braces in the interior wall.
I am pretty sure they are just for convenience during construction (e.g. a bother to remove once the frames are fully built or just there for drywall to be nailed into).
However, I am not an expert, so I wasn't sure if these were structural (maybe some type of shear wall support?) or not. In case it matters, the house was built in 1951 and is in western Georgia. All the wooden beams, including the angled ones, are held in place with 4inch nails.
Are these angle braces safe to remove and leave out? The entire cutaway area (sans drywall) would be a closet door with a frame of two 2x4s above and a vertical 2x4 on either side.
walls structural construction
edited Jan 4 at 17:28
isherwood
46k454117
asked Jan 3 at 23:23
TylerHTylerH
1799
add a comment |
I was helping a friend expand the width of a closet door, and when we pulled the drywall off the interior wall frame, we noticed some 45-degree wall braces in the interior wall.
I am pretty sure they are just for convenience during construction (e.g. a bother to remove once the frames are fully built or just there for drywall to be nailed into).
However, I am not an expert, so I wasn't sure if these were structural (maybe some type of shear wall support?) or not. In case it matters, the house was built in 1951 and is in western Georgia. All the wooden beams, including the angled ones, are held in place with 4inch nails.
Are these angle braces safe to remove and leave out? The entire cutaway area (sans drywall) would be a closet door with a frame of two 2x4s above and a vertical 2x4 on either side.
walls structural construction
edited Jan 4 at 17:28
isherwood
46k454117
asked Jan 3 at 23:23
TylerHTylerH
1799
2
Not that it matters much, but this is not 45°
– pipe
Jan 4 at 9:26
@pipe I'm aware, I just felt like it was the easiest descriptor that would be easily recognized as "not at a right angle", short of whipping out a protractor.
– TylerH
Jan 4 at 14:43
add a comment |
I was helping a friend expand the width of a closet door, and when we pulled the drywall off the interior wall frame, we noticed some 45-degree wall braces in the interior wall.
I am pretty sure they are just for convenience during construction (e.g. a bother to remove once the frames are fully built or just there for drywall to be nailed into).
However, I am not an expert, so I wasn't sure if these were structural (maybe some type of shear wall support?) or not. In case it matters, the house was built in 1951 and is in western Georgia. All the wooden beams, including the angled ones, are held in place with 4inch nails.
Are these angle braces safe to remove and leave out? The entire cutaway area (sans drywall) would be a closet door with a frame of two 2x4s above and a vertical 2x4 on either side.
walls structural construction
edited Jan 4 at 17:28
isherwood
46k454117
asked Jan 3 at 23:23
TylerHTylerH
1799
I was helping a friend expand the width of a closet door, and when we pulled the drywall off the interior wall frame, we noticed some 45-degree wall braces in the interior wall.
I am pretty sure they are just for convenience during construction (e.g. a bother to remove once the frames are fully built or just there for drywall to be nailed into).
However, I am not an expert, so I wasn't sure if these were structural (maybe some type of shear wall support?) or not. In case it matters, the house was built in 1951 and is in western Georgia. All the wooden beams, including the angled ones, are held in place with 4inch nails.
Are these angle braces safe to remove and leave out? The entire cutaway area (sans drywall) would be a closet door with a frame of two 2x4s above and a vertical 2x4 on either side.
walls structural construction
walls structural construction
edited Jan 4 at 17:28
isherwood
46k454117
asked Jan 3 at 23:23
TylerHTylerH
1799
edited Jan 4 at 17:28
isherwood
46k454117
asked Jan 3 at 23:23
TylerHTylerH
1799
edited Jan 4 at 17:28
isherwood
46k454117
edited Jan 4 at 17:28
isherwood
46k454117
edited Jan 4 at 17:28
isherwood
46k454117
46k454117
asked Jan 3 at 23:23
TylerHTylerH
1799
asked Jan 3 at 23:23
TylerHTylerH
1799
asked Jan 3 at 23:23
TylerHTylerH
1799
1799
2
Not that it matters much, but this is not 45°
– pipe
Jan 4 at 9:26
@pipe I'm aware, I just felt like it was the easiest descriptor that would be easily recognized as "not at a right angle", short of whipping out a protractor.
– TylerH
Jan 4 at 14:43
add a comment |
2
Not that it matters much, but this is not 45°
– pipe
Jan 4 at 9:26
@pipe I'm aware, I just felt like it was the easiest descriptor that would be easily recognized as "not at a right angle", short of whipping out a protractor.
– TylerH
Jan 4 at 14:43
2
2
Not that it matters much, but this is not 45°
– pipe
Jan 4 at 9:26
Not that it matters much, but this is not 45°
– pipe
Jan 4 at 9:26
@pipe I'm aware, I just felt like it was the easiest descriptor that would be easily recognized as "not at a right angle", short of whipping out a protractor.
– TylerH
Jan 4 at 14:43
@pipe I'm aware, I just felt like it was the easiest descriptor that would be easily recognized as "not at a right angle", short of whipping out a protractor.
– TylerH
Jan 4 at 14:43
add a comment |
3 Answers
3
active
oldest
votes
Temporary braces are nailed to the face of the wall, not fit into it. That was intended as a structural member by the carpenter.
That said, it's almost certainly not critical. The entirety of the other nearby walls and the roof structure likely provide many times what that one brace does in diagonal support. Also, you don't see that technique used anymore.
I wouldn't hesitate to remove the portion that impedes your progress.
I do suggest a doubled stud, however, and you might want to orient at least one of your header members vertically, for stiffness:
__
| |
| |
| |
|__|____
|_______|
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
When you say orient one header vertically, do you mean like|_as opposed to||(looking down the long axis of the headers)?
– TylerH
Jan 4 at 2:52
1
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@AndyT I see. Well, the plan was to go with||originally, not=; I'm not sure if the wall framing can fit something in the shape of|_, but since isherwood said "at least one", I assume||is best.
– TylerH
Jan 4 at 14:45
1
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
add a comment |
Sometimes framing of a short internal wall that TEE's into an exterior wall is braced that way if the exterior wall is:
- The exterior wall extends a long distance on either side of the TEE
- And the exterior wall is parallel to ceiling joists and floor joists
- And has a high gable end wall above this area.
Intention was to eliminate a lot of flex in the exterior wall both during construction and when there is possibility of large gusty wind loads on the wall. You will see less of this with much construction moving toward 2x6 studding for exterior walls. Metal X banding nailed to the face of the studs is also a better way to achieve this result.
Repeating from Isherwood. Make sure to put double stud at the left and right side of your opening. A single 2x4 is just not stiff enough and you will really appreciate it being there when you come to install door casing or trim.
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
add a comment |
We have a few of those in our walls. Local code does not require them but our builder was from a place with an appreciable earthquake threat and it was cheaper to build with the existing plans than draw up new ones lacking the earthquake bracing.
Unless the builder was lying that's earthquake bracing.
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
add a comment |
Your Answer
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "73"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f154034%2fare-these-integrated-diagonal-wall-braces-structurally-important%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
Temporary braces are nailed to the face of the wall, not fit into it. That was intended as a structural member by the carpenter.
That said, it's almost certainly not critical. The entirety of the other nearby walls and the roof structure likely provide many times what that one brace does in diagonal support. Also, you don't see that technique used anymore.
I wouldn't hesitate to remove the portion that impedes your progress.
I do suggest a doubled stud, however, and you might want to orient at least one of your header members vertically, for stiffness:
__
| |
| |
| |
|__|____
|_______|
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
When you say orient one header vertically, do you mean like|_as opposed to||(looking down the long axis of the headers)?
– TylerH
Jan 4 at 2:52
1
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@AndyT I see. Well, the plan was to go with||originally, not=; I'm not sure if the wall framing can fit something in the shape of|_, but since isherwood said "at least one", I assume||is best.
– TylerH
Jan 4 at 14:45
1
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
add a comment |
Temporary braces are nailed to the face of the wall, not fit into it. That was intended as a structural member by the carpenter.
That said, it's almost certainly not critical. The entirety of the other nearby walls and the roof structure likely provide many times what that one brace does in diagonal support. Also, you don't see that technique used anymore.
I wouldn't hesitate to remove the portion that impedes your progress.
I do suggest a doubled stud, however, and you might want to orient at least one of your header members vertically, for stiffness:
__
| |
| |
| |
|__|____
|_______|
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
When you say orient one header vertically, do you mean like|_as opposed to||(looking down the long axis of the headers)?
– TylerH
Jan 4 at 2:52
1
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@AndyT I see. Well, the plan was to go with||originally, not=; I'm not sure if the wall framing can fit something in the shape of|_, but since isherwood said "at least one", I assume||is best.
– TylerH
Jan 4 at 14:45
1
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
add a comment |
Temporary braces are nailed to the face of the wall, not fit into it. That was intended as a structural member by the carpenter.
That said, it's almost certainly not critical. The entirety of the other nearby walls and the roof structure likely provide many times what that one brace does in diagonal support. Also, you don't see that technique used anymore.
I wouldn't hesitate to remove the portion that impedes your progress.
I do suggest a doubled stud, however, and you might want to orient at least one of your header members vertically, for stiffness:
__
| |
| |
| |
|__|____
|_______|
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
Temporary braces are nailed to the face of the wall, not fit into it. That was intended as a structural member by the carpenter.
That said, it's almost certainly not critical. The entirety of the other nearby walls and the roof structure likely provide many times what that one brace does in diagonal support. Also, you don't see that technique used anymore.
I wouldn't hesitate to remove the portion that impedes your progress.
I do suggest a doubled stud, however, and you might want to orient at least one of your header members vertically, for stiffness:
__
| |
| |
| |
|__|____
|_______|
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
edited Jan 4 at 14:48
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
answered Jan 4 at 0:31
isherwoodisherwood
46k454117
46k454117
When you say orient one header vertically, do you mean like|_as opposed to||(looking down the long axis of the headers)?
– TylerH
Jan 4 at 2:52
1
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@AndyT I see. Well, the plan was to go with||originally, not=; I'm not sure if the wall framing can fit something in the shape of|_, but since isherwood said "at least one", I assume||is best.
– TylerH
Jan 4 at 14:45
1
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
add a comment |
When you say orient one header vertically, do you mean like|_as opposed to||(looking down the long axis of the headers)?
– TylerH
Jan 4 at 2:52
1
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@AndyT I see. Well, the plan was to go with||originally, not=; I'm not sure if the wall framing can fit something in the shape of|_, but since isherwood said "at least one", I assume||is best.
– TylerH
Jan 4 at 14:45
1
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
When you say orient one header vertically, do you mean like
|_ as opposed to || (looking down the long axis of the headers)?– TylerH
Jan 4 at 2:52
When you say orient one header vertically, do you mean like
|_ as opposed to || (looking down the long axis of the headers)?– TylerH
Jan 4 at 2:52
1
1
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@TylerH - No, he means |_ as opposed to =
– AndyT
Jan 4 at 9:07
@AndyT I see. Well, the plan was to go with
|| originally, not =; I'm not sure if the wall framing can fit something in the shape of |_, but since isherwood said "at least one", I assume || is best.– TylerH
Jan 4 at 14:45
@AndyT I see. Well, the plan was to go with
|| originally, not =; I'm not sure if the wall framing can fit something in the shape of |_, but since isherwood said "at least one", I assume || is best.– TylerH
Jan 4 at 14:45
1
1
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
You'd put the horizontal member on the bottom.
– isherwood
Jan 4 at 14:47
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
@TylerH - Looking on plan, the studs in a wall look something like: | | | | | |. In order to then have your header the same width as the studs, your header is then laid flat / horizontally, i.e. like _ when looking down its axis. isherwood's recommendation is to do a doubled header, with the second header rotated to give greater vertical bending stiffness.
– AndyT
Jan 4 at 14:52
add a comment |
Sometimes framing of a short internal wall that TEE's into an exterior wall is braced that way if the exterior wall is:
- The exterior wall extends a long distance on either side of the TEE
- And the exterior wall is parallel to ceiling joists and floor joists
- And has a high gable end wall above this area.
Intention was to eliminate a lot of flex in the exterior wall both during construction and when there is possibility of large gusty wind loads on the wall. You will see less of this with much construction moving toward 2x6 studding for exterior walls. Metal X banding nailed to the face of the studs is also a better way to achieve this result.
Repeating from Isherwood. Make sure to put double stud at the left and right side of your opening. A single 2x4 is just not stiff enough and you will really appreciate it being there when you come to install door casing or trim.
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
add a comment |
Sometimes framing of a short internal wall that TEE's into an exterior wall is braced that way if the exterior wall is:
- The exterior wall extends a long distance on either side of the TEE
- And the exterior wall is parallel to ceiling joists and floor joists
- And has a high gable end wall above this area.
Intention was to eliminate a lot of flex in the exterior wall both during construction and when there is possibility of large gusty wind loads on the wall. You will see less of this with much construction moving toward 2x6 studding for exterior walls. Metal X banding nailed to the face of the studs is also a better way to achieve this result.
Repeating from Isherwood. Make sure to put double stud at the left and right side of your opening. A single 2x4 is just not stiff enough and you will really appreciate it being there when you come to install door casing or trim.
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
add a comment |
Sometimes framing of a short internal wall that TEE's into an exterior wall is braced that way if the exterior wall is:
- The exterior wall extends a long distance on either side of the TEE
- And the exterior wall is parallel to ceiling joists and floor joists
- And has a high gable end wall above this area.
Intention was to eliminate a lot of flex in the exterior wall both during construction and when there is possibility of large gusty wind loads on the wall. You will see less of this with much construction moving toward 2x6 studding for exterior walls. Metal X banding nailed to the face of the studs is also a better way to achieve this result.
Repeating from Isherwood. Make sure to put double stud at the left and right side of your opening. A single 2x4 is just not stiff enough and you will really appreciate it being there when you come to install door casing or trim.
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
Sometimes framing of a short internal wall that TEE's into an exterior wall is braced that way if the exterior wall is:
- The exterior wall extends a long distance on either side of the TEE
- And the exterior wall is parallel to ceiling joists and floor joists
- And has a high gable end wall above this area.
Intention was to eliminate a lot of flex in the exterior wall both during construction and when there is possibility of large gusty wind loads on the wall. You will see less of this with much construction moving toward 2x6 studding for exterior walls. Metal X banding nailed to the face of the studs is also a better way to achieve this result.
Repeating from Isherwood. Make sure to put double stud at the left and right side of your opening. A single 2x4 is just not stiff enough and you will really appreciate it being there when you come to install door casing or trim.
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
answered Jan 4 at 1:08
Michael Karas♦Michael Karas
43.7k43482
43.7k43482
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
add a comment |
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
The last reno I did on a balloon construction, the bisecting (middle) interior walls on both floors were to be sheathed in plywood to prevent racking of the house.
– Mazura
Jan 4 at 5:29
add a comment |
We have a few of those in our walls. Local code does not require them but our builder was from a place with an appreciable earthquake threat and it was cheaper to build with the existing plans than draw up new ones lacking the earthquake bracing.
Unless the builder was lying that's earthquake bracing.
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
add a comment |
We have a few of those in our walls. Local code does not require them but our builder was from a place with an appreciable earthquake threat and it was cheaper to build with the existing plans than draw up new ones lacking the earthquake bracing.
Unless the builder was lying that's earthquake bracing.
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
add a comment |
We have a few of those in our walls. Local code does not require them but our builder was from a place with an appreciable earthquake threat and it was cheaper to build with the existing plans than draw up new ones lacking the earthquake bracing.
Unless the builder was lying that's earthquake bracing.
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
We have a few of those in our walls. Local code does not require them but our builder was from a place with an appreciable earthquake threat and it was cheaper to build with the existing plans than draw up new ones lacking the earthquake bracing.
Unless the builder was lying that's earthquake bracing.
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
answered Jan 4 at 5:59
Loren PechtelLoren Pechtel
749412
749412
add a comment |
add a comment |
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f154034%2fare-these-integrated-diagonal-wall-braces-structurally-important%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
2
Not that it matters much, but this is not 45°
– pipe
Jan 4 at 9:26
@pipe I'm aware, I just felt like it was the easiest descriptor that would be easily recognized as "not at a right angle", short of whipping out a protractor.
– TylerH
Jan 4 at 14:43